Buy or Renew
Buy or Renew
Cisco + Splunk: It’s a new day for your data. Learn more.
 
cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
Start a conversation
1451
Views
0
Helpful
3
Replies

vlan protocol down on NM-16ESW port installed in 3725 router

Go to solution
sakengineer
Level 1
Level 1

‎12-24-2008 07:22 PM - edited ‎03-06-2019 03:08 AM

Hello all,

I have been struggling with a problem and not sure how to fix this.

I have confirmed etherswitch nm-16esw mod in 3725 router. I have created 2 vlans for voice and data under vlan database. I have created SVI's for these vlans on the router and define ip helper-address.

I have two IP phones connected with etherswitch port 1 and port 2 so that they can send the dhcp request to register over the WAN with Call Manager.

Now the issue is I couldn't get the VLAN data and voice to be up up. The line protocol is constantly down on them.

I am running c3725-adventerprisek9_ivs-mz.124-3j on 3725. Following are my configs:

interface Loopback0

ip address 10.61.65.254 255.255.255.0

!

interface FastEthernet0/0

no ip address

shutdown

duplex auto

speed auto

!

interface FastEthernet0/1

no ip address

shutdown

duplex auto

speed auto

!

interface FastEthernet1/0

description SiteB-Ph1

switchport trunk native vlan 63

switchport mode trunk

switchport voice vlan 306

spanning-tree portfast

no routing dynamic

!

interface FastEthernet1/1

switchport trunk native vlan 63

switchport mode trunk

switchport voice vlan 306

spanning-tree portfast

!

interface FastEthernet1/2

!

interface FastEthernet1/3

!

interface FastEthernet1/4

!

interface FastEthernet1/5

!

interface FastEthernet1/6

!

interface FastEthernet1/7

!

interface FastEthernet1/8

!

interface FastEthernet1/9

!

interface FastEthernet1/10

!

interface FastEthernet1/11

!

interface FastEthernet1/12

!

interface FastEthernet1/13

!

interface FastEthernet1/14

!

interface FastEthernet1/15

!

interface Serial2/0

no ip address

encapsulation frame-relay

serial restart-delay 0

no dce-terminal-timing-enable

frame-relay lmi-type cisco

!

interface Serial2/0.102 point-to-point

ip address 172.1.2.2 255.255.255.0

frame-relay interface-dlci 102

!

interface Serial2/1

no ip address

shutdown

serial restart-delay 0

no dce-terminal-timing-enable

!

interface Serial2/2

no ip address

shutdown

serial restart-delay 0

no dce-terminal-timing-enable

!

interface Serial2/3

no ip address

shutdown

serial restart-delay 0

no dce-terminal-timing-enable

!

interface Vlan1

no ip address

!

interface Vlan92

description Data Vlan

ip address 10.106.65.254 255.255.255.0

ip helper-address 10.6.64.11

!

interface Vlan104

description Voice Vlan

ip address 10.206.65.254 255.255.255.0

ip helper-address 10.60.64.11

!

router ospf 1

log-adjacency-changes

network 10.0.0.0 0.255.255.255 area 0

network 172.0.0.0 0.255.255.255 area 0

=================vlan database=========

VLAN ISL Id: 92

Name: Data

Media Type: Ethernet

VLAN 802.10 Id: 100063

State: Operational

MTU: 1500

VLAN ISL Id: 104

Name: Voice

Media Type: Ethernet

VLAN 802.10 Id: 100306

State: Operational

MTU: 1500

Also, I have noticed that etherswitch ports fa 1/7 and fa 1/15 keep flaping even though I have not configured anything

Labels:
0 Helpful
1 Accepted Solution

Accepted Solutions

Go to solution
richard.m.gilbert
Level 1
Level 1

‎12-24-2008 09:51 PM

If I understand it correctly, you have a phone and a computer plugged in on both interface 1/0 and 1/1? If so, I think you want to have those interfaces configured as shown below ...

!

!

interface FastEthernet1/0

description SiteB-Ph1

switchport access vlan 92

switchport voice vlan 104

switchport mode access

spanning-tree portfast

no routing dynamic

!

interface FastEthernet1/1

switchport access vlan 92

switchport voice vlan 104

switchport mode access

spanning-tree portfast

no routing dynamic

!

!

As for fa1/7 and 1/15 ... have you taken the module out and blown out the bay in the router as well as the module? That might help.

View solution in original post

0 Helpful
3 Replies 3

Go to solution
glen.grant
VIP Alumni
VIP Alumni

‎12-24-2008 07:47 PM

A lot of times you do not trunk the access ports that the phones are attached to . Set it up as a access port vlan 92 with a voice vlan 104 and get rid of the trunk statement and see what happens . If the SVI isn't up usually the port is not connected. I didn't understand the voice vlan setup , on the ports you have the voice vlan as 306 yet your definition in the vlan database and the SVI say 104 .

0 Helpful

Go to solution
sakengineer
Level 1
Level 1
In response to glen.grant

‎12-24-2008 08:29 PM

Thanks Glen.

Please read the voice vlan as 104 and data vlan as 92. I copied the old configuration for fa 0/1 and fa 0/2.

I'll give it a try and will update you.

SAK

0 Helpful

Go to solution
richard.m.gilbert
Level 1
Level 1

‎12-24-2008 09:51 PM

If I understand it correctly, you have a phone and a computer plugged in on both interface 1/0 and 1/1? If so, I think you want to have those interfaces configured as shown below ...

!

!

interface FastEthernet1/0

description SiteB-Ph1

switchport access vlan 92

switchport voice vlan 104

switchport mode access

spanning-tree portfast

no routing dynamic

!

interface FastEthernet1/1

switchport access vlan 92

switchport voice vlan 104

switchport mode access

spanning-tree portfast

no routing dynamic

!

!

As for fa1/7 and 1/15 ... have you taken the module out and blown out the bay in the router as well as the module? That might help.

0 Helpful
Customers Also Viewed These Support Documents
Review Cisco Networking products for a $25 gift card