cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
840
Views
0
Helpful
6
Replies

Pushing FPD software to nodes using LMS

jpazahanick
Level 4
Level 4

I am trying to deploy FPD software to the sup-bootflash: on a number of 7600s. I have the software on one node as a tftp-server, and am trying the following netconfig job in enable mode

copy tftp://172.25.255.7/c7600-fpd-pkg.122-33.SRC2.pkg sup-bootdisk:

The job fails with the following error:

Command(s) failed on the device Insufficient no. of interactive responses(or timeout) for command: copy tftp://172.25.255.7/c7600-fpd-pkg.122-33.SRC2.pkg sup-bootdisk:. TFTP: Tftp is supported only for config mode commands. Insufficient no. of interactive responses(or timeout) for command: copy tftp://172.25.255.7/c7600-fpd-pkg.122-33.SRC2.pkg sup-bootdisk:.

I assume it's because the node is probably prompting something similar to Destination filename [c7600-fpd-pkg.122-33.SRC2.pkg]?

and expecting a <CR>..

Is there a way to send one in a netconfig job? Is there a better way to distribute FBD software to the 7600s?

1 Accepted Solution

Accepted Solutions

You can use interactive commands in Netconfig. Just add a "" anywhere a response is expected. For example:

copy tftp://172.25.255.7/c7600-fpd-pkg.122-33.SRC2.pkg sup-bootdisk:

If additional responses are required, specify them after the . For example:

copy tftp://172.25.255.7/c7600-fpd-pkg.122-33.SRC2.pkg sup-bootdisk:172.25.255.7c7600-fpd-pkg.122-33.SRC2.pkgsup-bootdisk:

View solution in original post

6 Replies 6

Joe Clarke
Cisco Employee
Cisco Employee

What version of RME is this?

RME 4.2.0

You can use interactive commands in Netconfig. Just add a "" anywhere a response is expected. For example:

copy tftp://172.25.255.7/c7600-fpd-pkg.122-33.SRC2.pkg sup-bootdisk:

If additional responses are required, specify them after the . For example:

copy tftp://172.25.255.7/c7600-fpd-pkg.122-33.SRC2.pkg sup-bootdisk:172.25.255.7c7600-fpd-pkg.122-33.SRC2.pkgsup-bootdisk:

I added the at the end, but still get the same error.

Command(s) failed on the device Insufficient no. of interactive responses(or timeout) for command: copy tftp://172.25.255.7/c7600-fpd-pkg.122-33.SRC2.pkg sup-bootdisk:. TFTP: Tftp is supported only for config mode commands. Insufficient no. of interactive responses(or timeout) for command: copy tftp://172.25.255.7/c7600-fpd-pkg.122-33.SRC2.pkg sup-bootdisk:.

I thought it might be a time out issue, so I set the timeout to 600 seconds (the transfer takes about 180 seconds).

Does this come into play?

TFTP: Tftp is supported only for config mode commands.

I am doing the job from enable mode, as I would in person.

That's fine. Exactly what does your template look like now, and when done manually, what prompts do you see?

When recreating the sequence manually, I found a second (Do you want to overwrite) prompt as I had manually done the transfer.

All is working. Thanks for the help!

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: