cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
1213
Views
0
Helpful
3
Replies

L2 pseudowire interworking ATM-Ethernet

p.diaz
Level 1
Level 1

Hello.

I am trying to configure a L2 pseudowire L2 that ejecutes inteworking in the following topology

the pswudowire is not active buy I don't find anything wrong in the configuration. I Have tried with in and ethernet interworking but the pseudowire alway remais as showed below

(CPE1 FRAME RELAY)---alcatel cloud inteworking----ATM---(PE1)--MPLS--(PEP2)-VLAN44--(CPE2 VLAN 44)

((PE1 Configuration- cisco 12410/PRP, disk0:c12kprp-k4p-mz.120-32.SY7.bin))

pseudowire-class inter-ether

encapsulation mpls

interworking ip

Current configuration : 275 bytes

!

interface ATM0/0.5 point-to-point

description ### Prueba interworking ATM-Ethernet ####

mtu 1500

no ip directed-broadcast

no atm enable-ilmi-trap

snmp trap link-status

pvc 0/10 l2transport

encapsulation aal5snap

xconnect 10.19.1.4 10 pw-class inter-ether

!

end

PEC12COL01#show mpls l2transport vc deta

Local interface: AT0/0.5 up, line protocol up, ATM AAL5 0/10 up

MPLS VC type is ATM AAL5, interworking type is IP

Destination address: 10.19.1.4, VC ID: 10, VC status: down

Create time: 01:06:05, last status change time: 00:00:34

Signaling protocol: LDP, peer 10.19.1.4:0 up

MPLS VC labels: local 297, remote unassigned

Group ID: local 0, remote unknown

MTU: local 1500, remote unknown

Remote interface description:

Sequencing: receive disabled, send disabled

VC statistics:

packet totals: receive 0, send 0

byte totals: receive 0, send 0

packet drops: receive 0, seq error 0, send 0

=================================================================================

=================================================================================

((PE2 Configuration, CISCO7609, c7600s72033-adventerprisek9-mz.122-33.SRC2.bin))

pseudowire-class inter-ether

encapsulation mpls

interworking ip

!

PEP76CAN01#sh run int GigabitEthernet8/20

Building configuration...

Current configuration : 76 bytes

!

interface GigabitEthernet8/20

no ip address

speed 100

duplex full

end

!

interface GigabitEthernet8/20.10

encapsulation dot1Q 44

xconnect 10.19.1.16 10 pw-class inter-ether

end

PEP76CAN01#show mpls l2transport vc detail

Local interface: Gi8/20.10 up, line protocol up, Eth VLAN 44 up

MPLS VC type is Eth VLAN, interworking type is IP

Destination address: 10.19.1.16, VC ID: 10, VC status: down

Output interface: none, imposed label stack {}

Preferred path: not configured

Default path: no route

No adjacency

Create time: 00:53:11, last status change time: 00:29:31

Signaling protocol: LDP, peer unknown

Targeted Hello: 10.19.1.4(LDP Id) -> 10.19.1.16

Status TLV support (local/remote) : enabled/unknown (no remote binding)

Label/status state machine : local standby, AC-ready, LnuRnd

Last local dataplane status rcvd: no fault

Last local SSS circuit status rcvd: no fault

Last local SSS circuit status sent: not sent

Last local LDP TLV status sent: not sent

Last remote LDP TLV status rcvd: unknown (no remote binding)

MPLS VC labels: local 27, remote unassigned

Group ID: local 0, remote unknown

MTU: local 1500, remote unknown

Remote interface description:

Sequencing: receive disabled, send disabled

VC statistics:

packet totals: receive 0, send 0

byte totals: receive 0, send 0

packet drops: receive 0, seq error 0, send 0

PEP76CAN01#

3 Replies 3

p.diaz
Level 1
Level 1

CPE1 status of the DLCI

RP-MPLS-MAQT-CAN#SHO FRAME-relay PVC 17

PVC Statistics for interface Serial0/0:0 (Frame Relay DTE)

DLCI = 17, DLCI USAGE = LOCAL, PVC STATUS = INACTIVE, INTERFACE = Serial0/0:0.17

input pkts 0 output pkts 0 in bytes 0

out bytes 0 dropped pkts 0 in pkts dropped 0

out pkts dropped 0 out bytes dropped 0

in FECN pkts 0 in BECN pkts 0 out FECN pkts 0

out BECN pkts 0 in DE pkts 0 out DE pkts 0

out bcast pkts 0 out bcast bytes 0

30 second input rate 0 bits/sec, 0 packets/sec

30 second output rate 0 bits/sec, 0 packets/sec

pvc create time 00:30:32, last time pvc status changed 00:30:14

RP-MPLS-MAQT-CAN#SHOW IP INTER BRIE

Interface IP-Address OK? Method Status Protocol

Serial0/0:0.17 1.1.1.2 YES manual down down

Hello

Did you enabled directed ldp session between two edge Pe of the MPLS network which is a necessity for your l2 pseudowire to come up in mpls.

Tarun

Hello Pedro,

I notice that second PE doesn't see up the ATM PE

Signaling protocol: LDP, peer unknown

Targeted Hello: 10.19.1.4(LDP Id) -> 10.19.1.16

while the first PE says:

that it sees the peer up.

So verify ip routing for loopback interfaces the ip addresses have to be published in your IGP routing protocol and be also advertised by LDP to create external MPLS label (end-to-end LSP with destination remote loopback ip address).

Another possible issue is the ATM/FR interworking part, the FR DTE says its FR subif is down down and the pvc is inactive.

Verify if Alcatel network is correctly configured to create a PVC with that DLCI on the FR side and that arrives on the ATM PE node.

Hope to help

Giuseppe

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: