cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
2349
Views
0
Helpful
7
Replies

Upgrade IOS Cisco 7204VXR

jomassanell
Level 1
Level 1

Hi,

I'm trying to upgrade IOS in Cisco 7204VXR.

Actually, it's working c7200-ik9s-mz.123-5a. I've tried to upgrade to c7200-ik9s-mz.124-23, and I've change boot system to disk2:c7200-ik9s-mz.124-23.bin, and other IOS, but everytime I restart the router, 7204VXR start with old IOS.

Also, I'm tried to delete old IOS, but router cannot load any new IOS.

Can you help me?

Thank you,

7 Replies 7

Kerem Gursu
Level 1
Level 1

Hi ,

After putting the line

boot system flash disk2:c7200-ik9s-mz.124-23.bin , did you erase the old configuration line pointing the old image which is above ?

HTH,

Kerem

Joan

To follow up the good suggestion from Kerem, it might help us figure out what is the issue if you would post the output of show run | include boot

HTH

Rick

HTH

Rick

Everytime I upload a new IOS, I execute:

- no boot system

- boot system flash disk2:ios

Router#dir disk2:

Directory of disk2:/

1 -rw- 28776396 Aug 31 2004 15:25:28 +00:00 c7200-ik9s-mz.124-23.bin

2 -rw- 18613056 Aug 31 2004 15:27:36 +00:00 c7200-ik9s-mz.123-5a.bin

128030720 bytes total (80640000 bytes free)

Router#sh bootvar

BOOT variable = c7200-ik9s-mz.124-23.bin,1;

CONFIG_FILE variable =

BOOTLDR variable = bootflash:c7200-kboot-mz.123-5.bin

Configuration register is 0x2102

Regards,

Joan

This information is helpful. It does show that the new IOS is on disk2 and that the boot variable is set to the new IOS. If it is not booting the new IOS there must still be some issue. Perhaps there is some issue with the new IOS at boot time. It would be helpful if you would post all the messages sent to the console during the boot process.

HTH

Rick

HTH

Rick

I attach console output. Remark that actually i'm tried to execute the new IOS by means of boot system flash c7200-ik9s-mz.124-23.bin, but I've tried to execute boot system flash disk2:c7200-ik9s-mz.124-23.bin and the output is the same.

Joan

Thank you for posting the console messages. It does not show any error that would explain why the new IOS does not boot. If you do show flash, do you see the new IOS in flash? If so then boot system flash should work. If not then please configure with boot system disk2, reload and post the console messages.

HTH

Rick

HTH

Rick

Is not possible configure either boot system disk2, neither can execute sh flash: or dir flash:

I tried to enter in rommon mode, and console output shows this message when I push Ctrl+Pause:

*** TLB (Load/Fetch) Exception ***

Access address = 0x0

PC = 0x00000000, SP = 0x80005d98, RA = 0x00000000

Cause Reg = 0x00000008, Status Reg = 0x3040d003

ROM Monitor Can Not Recover From Exception

A Board Reset Is Issued

*** Software NMI ***

PC = 0xbfc23680, SP = 0x80005c08, RA = 0xbfc104ac

Cause Reg = 0x00008008, Status Reg = 0x3048d007

CPU Registers:

ZERO = 0x00000000, AT = 0x00020000, V0 = 0xbe840300, V1 = 0xa0000000

A0 = 0xbfc27a10, A1 = 0x0000000d, A2 = 0x80005c0c, A3 = 0x00000000

T0 = 0x54079b83, T1 = 0x00000000, T2 = 0x00000000, T3 = 0x00000000

T4 = 0xd007ffe0, T5 = 0x00000000, T6 = 0xc9800500, T7 = 0xc9800500

S0 = 0x00000000, S1 = 0x80005c60, S2 = 0xbfc27840, S3 = 0x00000009

S4 = 0x80005e70, S5 = 0x00000002, S6 = 0xbfc2f224, S7 = 0x00000003

T8 = 0x3040d001, T9 = 0x00000000, K0 = , K1 =

GP = 0x63005428, SP = 0x80005c08, S8 = 0x00002102, RA = 0xbfc104ac

SREG = 0x3048d007, BADVADDR = 0x00000000, CAUSE = 0x00008008

EPC = 0x00000000, ERR_EPC = 0xbfc23680

System Return Info:

count: 19, reason: user reload

pc:0x607e0ef0, error address: 0x0

Stack Trace:

FP: 0x6412f1b8, PC: 0x607e0ef0

FP: 0x6412f1b8, PC: 0x607c5b9c

FP: 0x6412f1d0, PC: 0x607e6ef8

FP: 0x6412f270, PC: 0x60730120

FP: 0x6412f390, PC: 0x6071d97c

FP: 0x6412f3f0, PC: 0x6072ee24

FP: 0x6412f480, PC: 0x607aa320

FP: 0x6412f498, PC: 0x607aa304

Then, it restarts newly in normal mode.

Thanks

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: