Installing 2nd WIC card in Cisco 2811 router

Unanswered Question
Jan 27th, 2009
User Badges:

Hello,


I'd like to know the proper procedure for installation, please. Does it require the router to be powered off? Any help would be appreciated.


Best regards.


lf



  • 1
  • 2
  • 3
  • 4
  • 5
Overall Rating: 0 (0 ratings)
Loading.
Tshi M Tue, 01/27/2009 - 08:43
User Badges:
  • Silver, 250 points or more

here is a short step:

1. issue the "sh diag" to verify the slot

2. configure card type "card type t1 slot# where slot# is the one return from sh diag.


regards,

angelmed Tue, 01/27/2009 - 12:25
User Badges:

Thank you your help...I can't use "card" command though, not sure if it's because of IOS ver?:

Cisco IOS Software, 2800 Software (C2800NM-IPBASE-M), Version 12.4(3i), RELEASE SOFTWARE (fc2)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2007 by Cisco Systems, Inc.

Compiled Wed 28-Nov-07 21:09 by stshen


ROM: System Bootstrap, Version 12.4(13r)T, RELEASE SOFTWARE (fc1)


Router uptime is 19 weeks, 1 day, 2 hours, 59 minutes

System returned to ROM by power-on

System image file is "flash:c2800nm-ipbase-mz.124-3i.bin"


Cisco 2811 (revision 53.51) with 251904K/10240K bytes of memory.

Processor board ID FTX1234A0QF

2 FastEthernet interfaces

1 Serial interface

DRAM configuration is 64 bits wide with parity enabled.

239K bytes of non-volatile configuration memory.

62720K bytes of ATA CompactFlash (Read/Write)


Configuration register is 0x2102


Is it necessary to use this command?


thanks

paolo bevilacqua Tue, 01/27/2009 - 12:34
User Badges:
  • Super Gold, 25000 points or more
  • Hall of Fame,

    Founding Member

Only for T1/E1 cards.

Tshi M Tue, 01/27/2009 - 12:44
User Badges:
  • Silver, 250 points or more

I am not sure but it should work with ver 12.4

Are you issuing the command from the config mode? what do you get from sh diag?

angelmed Tue, 01/27/2009 - 12:57
User Badges:

I have not installed 2nd WIC card yet; I have WIC-1DSU-T1-V2 card already installed in WIC slot 0, for the existing T1 line.Still I can't use "card" command, so I'm afraid that I will not be able to make proper configuration for additional T1 line..



sh diag

Slot 0:

C2811 Motherboard with 2FE and integrated VPN Port adapter, 2 ports

Port adapter is analyzed

Port adapter insertion time unknown

EEPROM contents at hardware discovery:

PCB Serial Number : FOC12323XKT

Hardware Revision : 1.0

Top Assy. Part Number : 800-26920-04

Board Revision : A0

Deviation Number : 0

Fab Version : 04

RMA Test History : 00

RMA Number : 0-0-0-0

RMA History : 00

Processor type : 87

Hardware date code : 20080809

Chassis Serial Number : FTX1234A0QF

Chassis MAC Address : 0022.904d.8088

MAC Address block size : 24

CLEI Code : COM7R00ARA

Product (FRU) Number : CISCO2811

Part Number : 73-10258-05

Version Identifier : V05

--More-- EEPROM format version 4

EEPROM contents (hex):

0x00: 04 FF C1 8B 46 4F 43 31 32 33 32 33 58 4B 54 40

0x10: 03 E7 41 01 00 C0 46 03 20 00 69 28 04 42 41 30

0x20: 88 00 00 00 00 02 04 03 00 81 00 00 00 00 04 00

0x30: 09 87 83 01 32 68 A9 C2 8B 46 54 58 31 32 33 34

0x40: 41 30 51 46 C3 06 00 22 90 4D 80 88 43 00 18 C6

0x50: 8A 43 4F 4D 37 52 30 30 41 52 41 CB 8F 43 49 53

0x60: 43 4F 32 38 31 31 20 20 20 20 20 20 82 49 28 12

0x70: 05 89 56 30 35 20 D9 02 40 C1 FF FF FF FF FF FF


WIC Slot 0:

FT1 PMC4351

Hardware Revision : 1.2

PCB Serial Number : FOC122941SD

Part Number : 73-8346-05

Board Revision : A0

RMA Test History : 00

RMA Number : 0-0-0-0

RMA History : 00

Deviation Number : 0-0

Product (FRU) Number : WIC-1DSU-T1-V2

Top Assy. Part Number : 800-22193-03

CLEI Code : IPUIAPRRAA

EEPROM format version 4

EEPROM contents (hex):

0x00: 04 FF 40 00 52 41 01 02 C1 8B 46 4F 43 31 32 32

0x10: 39 34 31 53 44 82 49 20 9A 05 42 41 30 03 00 81

0x20: 00 00 00 00 04 00 80 00 00 00 00 CB 94 57 49 43

0x30: 2D 31 44 53 55 2D 54 31 2D 56 32 20 20 20 20 20

0x40: 20 C0 46 03 20 00 56 B1 03 C6 8A 49 50 55 49 41

0x50: 50 52 52 41 41 FF FF FF FF FF FF FF FF FF FF FF

0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF



paolo bevilacqua Tue, 01/27/2009 - 19:28
User Badges:
  • Super Gold, 25000 points or more
  • Hall of Fame,

    Founding Member

That is a T1 only card and you don't need to enter card type command

angelmed Wed, 01/28/2009 - 06:22
User Badges:

Thank you to all who responded to my question.


Regards,


lf

Actions

This Discussion