Trying to configure NM-32a on 2811

Answered Question
Jan 28th, 2009
User Badges:

I'm having a tough time configuring my Cisco 2811 Access Server. This router has the NM-32A card.


This is what I have done so far. I plugged the octal cable into bottom left port marked 8-15. I plugged cable # 2 into a switch that is turned on.


This is the output I am getting so far.


Tty Line Typ Tx/Rx A Modem Roty AccO AccI Uses Noise Overruns Int

* 0 0 CTY - - - - - 0 0 0/0 -

I 1 1 AUX 9600/9600 - - - - - 0 0 0/0 -

1/0 66 TTY 9600/9600 - - - - - 0 0 0/0 -

1/1 67 TTY 9600/9600 - - - - - 0 0 0/0 -

1/2 68 TTY 9600/9600 - - - - - 0 0 0/0 -

1/3 69 TTY 9600/9600 - - - - - 0 0 0/0 -

1/4 70 TTY 9600/9600 - - - - - 0 0 0/0 -

1/5 71 TTY 9600/9600 - - - - - 0 0 0/0 -

1/6 72 TTY 9600/9600 - - - - - 0 0 0/0 -

1/7 73 TTY 9600/9600 - - - - - 0 0 0/0 -

1/8 74 TTY 9600/9600 - - - - - 0 0 0/0 -

* 1/9 75 TTY 9600/9600 - - - - - 0 0 120/362 -

1/10 76 TTY 9600/9600 - - - - - 0 0 0/0 -

1/11 77 TTY 9600/9600 - - - - - 0 0 0/0 -

1/12 78 TTY 9600/9600 - - - - - 0 0 0/0 -

1/13 79 TTY 9600/9600 - - - - - 0 0 0/0 -

1/14 80 TTY 9600/9600 - - - - - 0 0 0/0 -

1/15 81 TTY 9600/9600 - - - - - 0 0 0/0 -

1/16 82 TTY 9600/9600 - - - - - 0 0 0/0 -

1/17 83 TTY 9600/9600 - - - - - 0 0 0/0 -

1/18 84 TTY 9600/9600 - - - - - 0 0 0/0 -

1/19 85 TTY 9600/9600 - - - - - 0 0 0/0 -

Tty Line Typ Tx/Rx A Modem Roty AccO AccI Uses Noise Overruns Int


1/20 86 TTY 9600/9600 - - - - - 0 0 0/0 -

1/21 87 TTY 9600/9600 - - - - - 0 0 0/0 -

1/22 88 TTY 9600/9600 - - - - - 0 0 0/0 -

1/23 89 TTY 9600/9600 - - - - - 0 0 0/0 -

1/24 90 TTY 9600/9600 - - - - - 0 0 0/0 -

1/25 91 TTY 9600/9600 - - - - - 0 0 0/0 -

1/26 92 TTY 9600/9600 - - - - - 0 0 0/0 -

1/27 93 TTY 9600/9600 - - - - - 0 0 0/0 -

1/28 94 TTY 9600/9600 - - - - - 0 0 0/0 -

1/29 95 TTY 9600/9600 - - - - - 0 0 0/0 -

1/30 96 TTY 9600/9600 - - - - - 0 0 0/0 -

1/31 97 TTY 9600/9600 - - - - - 0 0 0/0 -

322 322 VTY - - - - - 0 0 0/0 -

323 323 VTY - - - - - 0 0 0/0 -

324 324 VTY - - - - - 0 0 0/0 -

325 325 VTY - - - - - 0 0 0/0 -

326 326 VTY - - - - - 0 0 0/0 -


Line(s) not in async mode -or- with no hardware support:

2-65, 98-321




I created:


int loopback 199

ip add 1.1.1.1 255.255.255.255


ip host SW1 2009 1.1.1.1



Then I try this and fail:


Trying SW1 (1.1.1.1, 2009)...

% Connection refused by remote host




Am I doing something wrong??? Help??

Correct Answer by Roberto Salazar about 8 years 3 months ago

clear line 75 and try again. BTW, you configuration should be ip host SW1 2075 1.1.1.1 since the octal port 2 is line 75.

  • 1
  • 2
  • 3
  • 4
  • 5
Overall Rating: 5 (1 ratings)
Loading.
Correct Answer
Roberto Salazar Wed, 01/28/2009 - 12:24
User Badges:
  • Gold, 750 points or more

clear line 75 and try again. BTW, you configuration should be ip host SW1 2075 1.1.1.1 since the octal port 2 is line 75.

cisconoobie Wed, 01/28/2009 - 12:26
User Badges:

#clear line 75


#SW1


Trying SW1 (1.1.1.1, 2075)...

% Connection refused by remote host



Please advise.

cisconoobie Wed, 01/28/2009 - 12:31
User Badges:

Ok it works now. I needed to put in:


# transport input all


under line 1/0 1/31


Thanks for help!

Roberto Salazar Wed, 01/28/2009 - 12:35
User Badges:
  • Gold, 750 points or more

Maybe you have not configure the line for the octal cable. can you post the following:

sh run | beg line

sho line


make sure you have "transport input all" under the line 1/0 1/x



Actions

This Discussion