Solved: Trying to configure NM-32a on 2811

cisconoobie · ‎01-28-2009

I'm having a tough time configuring my Cisco 2811 Access Server. This router has the NM-32A card.

This is what I have done so far. I plugged the octal cable into bottom left port marked 8-15. I plugged cable # 2 into a switch that is turned on.

This is the output I am getting so far.

Tty Line Typ Tx/Rx A Modem Roty AccO AccI Uses Noise Overruns Int

* 0 0 CTY - - - - - 0 0 0/0 -

I 1 1 AUX 9600/9600 - - - - - 0 0 0/0 -

1/0 66 TTY 9600/9600 - - - - - 0 0 0/0 -

1/1 67 TTY 9600/9600 - - - - - 0 0 0/0 -

1/2 68 TTY 9600/9600 - - - - - 0 0 0/0 -

1/3 69 TTY 9600/9600 - - - - - 0 0 0/0 -

1/4 70 TTY 9600/9600 - - - - - 0 0 0/0 -

1/5 71 TTY 9600/9600 - - - - - 0 0 0/0 -

1/6 72 TTY 9600/9600 - - - - - 0 0 0/0 -

1/7 73 TTY 9600/9600 - - - - - 0 0 0/0 -

1/8 74 TTY 9600/9600 - - - - - 0 0 0/0 -

* 1/9 75 TTY 9600/9600 - - - - - 0 0 120/362 -

1/10 76 TTY 9600/9600 - - - - - 0 0 0/0 -

1/11 77 TTY 9600/9600 - - - - - 0 0 0/0 -

1/12 78 TTY 9600/9600 - - - - - 0 0 0/0 -

1/13 79 TTY 9600/9600 - - - - - 0 0 0/0 -

1/14 80 TTY 9600/9600 - - - - - 0 0 0/0 -

1/15 81 TTY 9600/9600 - - - - - 0 0 0/0 -

1/16 82 TTY 9600/9600 - - - - - 0 0 0/0 -

1/17 83 TTY 9600/9600 - - - - - 0 0 0/0 -

1/18 84 TTY 9600/9600 - - - - - 0 0 0/0 -

1/19 85 TTY 9600/9600 - - - - - 0 0 0/0 -

Tty Line Typ Tx/Rx A Modem Roty AccO AccI Uses Noise Overruns Int

1/20 86 TTY 9600/9600 - - - - - 0 0 0/0 -

1/21 87 TTY 9600/9600 - - - - - 0 0 0/0 -

1/22 88 TTY 9600/9600 - - - - - 0 0 0/0 -

1/23 89 TTY 9600/9600 - - - - - 0 0 0/0 -

1/24 90 TTY 9600/9600 - - - - - 0 0 0/0 -

1/25 91 TTY 9600/9600 - - - - - 0 0 0/0 -

1/26 92 TTY 9600/9600 - - - - - 0 0 0/0 -

1/27 93 TTY 9600/9600 - - - - - 0 0 0/0 -

1/28 94 TTY 9600/9600 - - - - - 0 0 0/0 -

1/29 95 TTY 9600/9600 - - - - - 0 0 0/0 -

1/30 96 TTY 9600/9600 - - - - - 0 0 0/0 -

1/31 97 TTY 9600/9600 - - - - - 0 0 0/0 -

322 322 VTY - - - - - 0 0 0/0 -

323 323 VTY - - - - - 0 0 0/0 -

324 324 VTY - - - - - 0 0 0/0 -

325 325 VTY - - - - - 0 0 0/0 -

326 326 VTY - - - - - 0 0 0/0 -

Line(s) not in async mode -or- with no hardware support:

2-65, 98-321

I created:

int loopback 199

ip add 1.1.1.1 255.255.255.255

ip host SW1 2009 1.1.1.1

Then I try this and fail:

Trying SW1 (1.1.1.1, 2009)...

% Connection refused by remote host

Am I doing something wrong??? Help??

Roberto Salazar · ‎01-28-2009

clear line 75 and try again. BTW, you configuration should be ip host SW1 2075 1.1.1.1 since the octal port 2 is line 75.

View solution in original post

Roberto Salazar · ‎01-28-2009

clear line 75 and try again. BTW, you configuration should be ip host SW1 2075 1.1.1.1 since the octal port 2 is line 75.

cisconoobie · ‎01-28-2009

#clear line 75

#SW1

Trying SW1 (1.1.1.1, 2075)...

% Connection refused by remote host

Please advise.

cisconoobie · ‎01-28-2009

Ok it works now. I needed to put in:

# transport input all

under line 1/0 1/31

Thanks for help!

Roberto Salazar · ‎01-28-2009

Maybe you have not configure the line for the octal cable. can you post the following:

sh run | beg line

sho line

make sure you have "transport input all" under the line 1/0 1/x