Solved: Service-policy not working fine with ATM subint

James Lasky · ‎01-29-2009

Hi

I've a C1801 with IOS C180X Software (C180X-BROADBAND-M), Version 12.4(15)T1 experiencing a problem related to Qos.

The config is attached.

As soon as the ATM come up the "service-policy output cos-po2-bhw-atm-0-1-70" statement disapper from the config under ATM0.1 pvc 8/35.

*Jan 29 17:11:18: %LINK-3-UPDOWN: Interface ATM0, changed state to up

*Jan 29 17:11:19: %LINEPROTO-5-UPDOWN: Line protocol on Interface ATM0, changed state to up

*Jan 29 17:11:24: I/f ATM0.1 VC 8/35 class cos-map-bhw-fe-ge-0.0-vo requested bandwidth 80 (kbps), available only 0 (kbps)

*Jan 29 17:11:24: Service policy detach failed

#sh run interface atM 0.1

Building configuration...

Current configuration : 193 bytes

!

interface ATM0.1 point-to-point

bandwidth 128

ip address 10.205.1.22 255.255.255.252

no ip redirects

no ip proxy-arp

no snmp trap link-status

pvc 8/35

encapsulation aal5snap

!

Any idea ?

Tks

Ric

Giuseppe Larosa · ‎01-29-2009

Hello Riccardo,

on other threads about this someone has reported that to be able to apply a CBWFQ to an ATM subinterface you need to define under the pvc some ATM Class of service

the default is an UBR (unspecified bit rate) that has no guaranteed resources.

I would try to configure some BW resources for the pvc using vbr-nrt.

Hope to help

Giuseppe

View solution in original post

James Lasky · ‎01-29-2009

here's the config

C1801

!

class-map match-any cos-map-bhw-atm-0-0-1

match access-group name cos-map-acl-bhw-fe-0.0-vo

class-map match-any cos-map-bhw-fe-ge-0.0-bu

match access-group name cos-map-acl-bhw-fe-0.0-bu

class-map match-any cos-map-bhw-fe-ge-0.0-vo

match access-group name cos-map-acl-bhw-fe-0.0-vo

class-map match-any cos-map-bhw-fe-ge-0.0-st

match access-group name cos-map-acl-bhw-fe-0.0-st

!

policy-map cos-po2-bhw-atm-0-1-70

class cos-map-bhw-fe-ge-0.0-vo

priority 80

police 80000 conform-action transmit exceed-action transmit violate-action transmit

class cos-map-bhw-fe-ge-0.0-st

bandwidth 8

random-detect

class cos-map-bhw-fe-ge-0.0-bu

bandwidth 20

random-detect

class class-default

policy-map cos-map-bhw-fe-ge-0.0

class cos-map-bhw-fe-ge-0.0-vo

set ip dscp af41

class cos-map-bhw-fe-ge-0.0-st

set ip dscp af31

class cos-map-bhw-fe-ge-0.0-bu

set ip dscp af21

class class-default

set ip dscp af11

!

interface FastEthernet0

description Dati

ip address 192.168.116.49 255.255.255.240

duplex auto

speed auto

service-policy input cos-map-bhw-fe-ge-0.0

!

interface ATM0

bandwidth 4608

no ip address

no atm ilmi-keepalive

dsl operating-mode auto

!

interface ATM0.1 point-to-point

bandwidth 128

ip address 10.205.1.22 255.255.255.252

no ip redirects

no ip proxy-arp

pvc 8/35

encapsulation aal5snap

service-policy output cos-po2-bhw-atm-0-1-70

!

interface Vlan1

description Voip

ip address 192.168.116.145 255.255.255.240

ip tcp adjust-mss 1452

service-policy input cos-map-bhw-fe-ge-0.0

!

ip access-list extended cos-map-acl-bhw-fe-0.0-bu

permit ip any 192.168.28.0 0.0.0.255

ip access-list extended cos-map-acl-bhw-fe-0.0-st

remark *** Class Stream ***

deny ip any any

ip access-list extended cos-map-acl-bhw-fe-0.0-vo

permit ip any 192.168.52.0 0.0.0.255

permit ip any 192.168.53.0 0.0.0.255

remark *** Class Voice ***

!

etc

Giuseppe Larosa · ‎01-29-2009

Hello Riccardo,

on other threads about this someone has reported that to be able to apply a CBWFQ to an ATM subinterface you need to define under the pvc some ATM Class of service

the default is an UBR (unspecified bit rate) that has no guaranteed resources.

I would try to configure some BW resources for the pvc using vbr-nrt.

Hope to help

Giuseppe

James Lasky · ‎01-30-2009

Ciao Giuseppe,

using cbr and/or vbr-nrt seems working...

Tks for your help

Ric