01-31-2009 11:04 AM - edited 03-15-2019 03:53 PM
<p>I have a 2811 ISR and put in a PVDM2-32 and configured the PRI and everything was good until I tried to make some calls. I did some show voice dsp commands and I'm getting this error, can anyone point me in the right direction:</p>
<p>sh voice dsp group all<br />
DSP groups on slot 0:<br />
dsp 1:<br />
State: FAIL, firmware: 0.0.0<br />
Max signal/voice channel: 16/16<br />
Max credits: 240<br />
num_of_sig_chnls_allocated: 16<br />
Transcoding channels allocated: 0<br />
Group: FLEX_GROUP_VOICE, complexity: FLEX<br />
Shared credits: 240, reserved credits: 0<br />
Signaling channels allocated: 16<br />
Voice channels allocated: 0<br />
Credits used: 0</p>
<p>dsp 2:<br />
State: FAIL, firmware: 0.0.0<br />
Max signal/voice channel: 16/16<br />
Max credits: 240<br />
num_of_sig_chnls_allocated: 9<br />
Transcoding channels allocated: 0<br />
Group: FLEX_GROUP_VOICE, complexity: FLEX<br />
Shared credits: 240, reserved credits: 0<br />
Signaling channels allocated: 9<br />
Voice channels allocated: 0<br />
Credits used: 0</p>
<p> 0 DSP resource allocation failure</p>
<p><br />
sh voice dsp voice</p>
<p>DSP DSP DSPWARE CURR BOOT PAK TX/RX</p>
<p>TYPE NUM CH CODEC VERSION STATE STATE RST AI VOICEPORT TS ABORT PACK CO<br />
UNT<br />
==== === == ======== ========== ===== ======= === == ========= == ===== ========<br />
====<br />
edsp 0001 01 g729r8 p 0.1 IDLE 50/0/1.1<br />
edsp 0002 01 g729r8 p 0.1 IDLE 50/0/2.1<br />
edsp 0003 01 g729r8 p 0.1 IDLE 50/0/3.1<br />
edsp 0004 01 g729r8 p 0.1 IDLE 50/0/4.1</p>
<p>Warning! DSPs1, 2, in slot 0 are using non-default firmware from flash:<br />
This is not recommended, the default version is 23.8.0</p>
<p>----------------------------FLEX VOICE CARD 0 ------------------------------<br />
*DSP VOICE CHANNELS*</p>
<p>CURR STATE : (busy)inuse (b-out)busy out (bpend)busyout pending<br />
LEGEND : (bad)bad (shut)shutdown (dpend)download pending</p>
<p>DSP DSP DSPWARE CURR BOOT PAK TX/RX</p>
<p>TYPE NUM CH CODEC VERSION STATE STATE RST AI VOICEPORT TS ABRT PACK CO<br />
UNT<br />
===== === == ========= ========== ===== ======= === == ========= == ==== =======<br />
=====<br />
C5510 001 01 None 0.0.0 bad idle 0 0 0<br />
0/0<br />
C5510 001 02 None 0.0.0 bad idle 0 0 0<br />
0/0</p>
<p> </p>
01-31-2009 11:11 AM
Hi, it after reseating the module (try a different slot) still problems, the PVDM2 is for RMA.
01-31-2009 12:15 PM
If you're on 12.4 code, this would be a hardware problem. I believe we had some instances of things like this in 12.2-12.3 code with some software bugs.
Generally same as Paolo said - reseat the cards, and otherwise RMA the PVDM2-32.
-nick
01-31-2009 02:30 PM
Thanks all!
Working with tac now!
Thanks!
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: