1751 for a cable router

Unanswered Question

<p>Hi,</p>

<p>I bought this 1751 hoping that I can use it to replace my Netgear router. Below is the sho ver. Will this router capable of replacing the Netgear.</p>

<p>cisco1751#sho ver<br />

Cisco Internetwork Operating System Software <br />

IOS (tm) C1700 Software (C1700-K8O3SY7-M), Version 12.2(8)T5,  RELEASE SOFTWARE (fc1)<br />

TAC Support: <a href="http://www.cisco.com/tac">http://www.cisco.com/tac</a><br />

Copyright (c) 1986-2002 by cisco Systems, Inc.<br />

Compiled Fri 21-Jun-02 19:24 by ccai<br />

Image text-base: 0x80008108, data-base: 0x80D2EACC</p>

<p>ROM: System Bootstrap, Version 12.2(1r)XE1, RELEASE SOFTWARE (fc1)<br />

ROM: C1700 Software (C1700-Y-M), Version 12.2(13)T1,  RELEASE SOFTWARE (fc1)</p>

<p>cisco1751 uptime is 15 hours, 48 minutes<br />

System returned to ROM by power-on<br />

System image file is "flash:c1700-k8o3sy7-mz.122-8.T5.bin"</p>

<p>cisco 1751 (MPC860P) processor (revision 0x600) with 36864K/12288K bytes of memory.<br />

Processor board ID JAD06390282 (3061614917), with hardware revision 0000<br />

MPC860P processor: part number 5, mask 2<br />

Bridging software.<br />

X.25 software, Version 3.0.0.<br />

Basic Rate ISDN software, Version 1.1.<br />

1 Ethernet/IEEE 802.3 interface(s)<br />

1 FastEthernet/IEEE 802.3 interface(s)<br />

1 ISDN Basic Rate interface(s)<br />

1 Virtual Private Network (VPN) Module(s)<br />

32K bytes of non-volatile configuration memory.<br />

16384K bytes of processor board System flash (Read/Write)</p>

<p>Configuration register is 0x2102</p>

<p><br />

Thank you.</p>

  • 1
  • 2
  • 3
  • 4
  • 5
Overall Rating: 0 (0 ratings)
Loading.
ohassairi Sat, 01/31/2009 - 23:11
User Badges:
  • Silver, 250 points or more


what kind of internet connection you use: isdn, adsl,...?

Leo Laohoo Wed, 02/18/2009 - 16:34
User Badges:
  • Super Gold, 25000 points or more
  • Hall of Fame,

    The Hall of Fame designation is a lifetime achievement award based on significant overall achievements in the community. 

  • Cisco Designated VIP,

    2017 LAN, Wireless

I don't think this is possible. The only ADSL-related WIC cards the 1750 will support are the WIC-1ADSL, WIC-1SHDSL, WIC-1ADSL-I-DG and the WIC-1ADSL-DG.


Cisco 1751 Modular Access Router Data Sheet:


http://www.cisco.com/en/US/products/hw/routers/ps221/products_data_sheet09186a0080088719.html




davebarus Sun, 02/22/2009 - 01:49
User Badges:

Hello,


I don't know if this will work for sure but it looks like you will have to connect your cable modem into your ethernet port and configure the ethernet port to receive a DHCP from your cable provider like this:

router(config-if)#ip address dhcp


Then you'll probably want to create a default route towards your ISP (default gateway):

router(config)#ip route 0.0.0.0 0.0.0.0 e0


Configure your fastethernet interface (LAN):

router(config-if)#ip address 192.168.0.1 255.255.255.0



After that you'll probably want to specify set up DHCP on your router:

router(config)#ip dhcp excluded-address 192.168.0.1 (excludes your f0 ip)

router(config)#ip dhcp-pool INSIDECLIENTS

router(config-dhcp)#network 192.168.0.0 255.255.255.0

router(config-dhcp)#default-router 192.168.0.1

router(config-dhcp)#dns-server 4.2.2.2 (or your ISPs DNS server)

routeR(config)#no ip dhcp conflict logging


Then setup PAT:

routeR(config)#access-list 100 permit ip 192.168.0.0 0.0.0.255 any

router(config)#int e0

router(config-if)#ip nat outside

router(config-if)#ip nat inside source list 100 interface e0 overload

router(config)#int f0

router(config-if)#ip nat inside



I've haven't set this type of configuration up before, but this is where i'd start.


Good luck :)


Actions

This Discussion