02-06-2009 08:53 AM - edited 03-15-2019 04:03 PM
We've been using MGCP w/D channel backhaul in the past with no problems. I'm now trying to configure a Cisco 2851 with a PRI using H.323. I can't figure out why my POTS dial peer is showing "down" on "OUT STAT".
AD PRE PASS OUT
TAG TYPE MIN OPER PREFIX DEST-PATTERN FER THRU SESS-TARGET STAT PORT
1 voip up up ....... 1 syst ipv4:10.10.10.10
2 voip up up ....... 2 syst ipv4:10.10.10.11
10 pots up up .T 0 down 1/0:23
PRI Channel Statistics:
ISDN Se1/0:23, Channel [1-24]
Configured Isdn Interface (dsl) 0
Channel State (0=Idle 1=Proposed 2=Busy 3=Reserved 4=Restart 5=Maint_Pend)
Channel : 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4
State : 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 3
Service State (0=Inservice 1=Maint 2=Outofservice 8=MaintPend 9=OOSPend)
Channel : 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4
State : 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 2
controller T1 1/0
framing esf
linecode b8zs
pri-group timeslots 1-24
interface Serial1/0:23
description PRI
no ip address
no logging event link-status
isdn switch-type primary-ni
isdn incoming-voice voice
no cdp enable
dial-peer voice 1 voip
preference 1
destination-pattern .......
voice-class codec 1
voice-class h323 1
session target ipv4:10.10.10.10
incoming called-number .
dtmf-relay h245-signal h245-alphanumeric
no vad
!
dial-peer voice 2 voip
preference 2
destination-pattern .......
voice-class codec 1
voice-class h323 1
session target ipv4:10.10.10.11
incoming called-number .
dtmf-relay h245-signal h245-alphanumeric
no vad
!
dial-peer voice 10 pots
destination-pattern .T
incoming called-number .
direct-inward-dial
port 1/0:23
forward-digits all
Any help would be greatly appreciated.
02-06-2009 09:18 AM
Hi,
Can you post the output of your sh isdn status and sh ip interface brief
02-06-2009 09:20 AM
XXX-2851#show isdn status serial 1/0:23
Global ISDN Switchtype = primary-4ess
ISDN Serial1/0:23 interface
dsl 0, interface ISDN Switchtype = primary-ni
Layer 1 Status:
ACTIVE
Layer 2 Status:
TEI = 0, Ces = 1, SAPI = 0, State = TEI_ASSIGNED
Layer 3 Status:
0 Active Layer 3 Call(s)
Active dsl 0 CCBs = 0
The Free Channel Mask: 0x807FFFFF
Number of L2 Discards = 0, L2 Session ID = 1
Total Allocated ISDN CCBs = 0
BOA-2851#show ip interface brief
Interface IP-Address OK? Method Status Protocol
GigabitEthernet0/0 172.26.3.1 YES NVRAM up up
GigabitEthernet0/1 172.26.4.1 YES NVRAM up up
Serial0/1/0 unassigned YES NVRAM up up
Serial0/2/0 unassigned YES NVRAM down down
Serial0/3/0 unassigned YES NVRAM up up
Serial1/0:0 unassigned YES unset down down
Serial1/0:1 unassigned YES unset down down
Serial1/0:2 unassigned YES unset down down
Serial1/0:3 unassigned YES unset down down
Serial1/0:4 unassigned YES unset down down
Serial1/0:5 unassigned YES unset down down
Serial1/0:6 unassigned YES unset down down
Serial1/0:7 unassigned YES unset down down
Serial1/0:8 unassigned YES unset down down
Serial1/0:9 unassigned YES unset down down
Serial1/0:10 unassigned YES unset down down
Serial1/0:11 unassigned YES unset down down
Serial1/0:12 unassigned YES unset down down
Serial1/0:13 unassigned YES unset down down
Serial1/0:14 unassigned YES unset down down
Serial1/0:15 unassigned YES unset down down
Serial1/0:16 unassigned YES unset down down
Serial1/0:17 unassigned YES unset down down
Serial1/0:18 unassigned YES unset down down
Serial1/0:19 unassigned YES unset down down
Serial1/0:20 unassigned YES unset down down
Serial1/0:21 unassigned YES unset down down
Serial1/0:22 unassigned YES unset down down
Serial1/0:23 unassigned YES manual up up
02-06-2009 09:22 AM
Hello,
Layer 2 needs to say MULTIPLE_FRAME_ESTABLISHED. Do term mon and debug isdn q921 and see what the output is and post it.
Hope that helped, if so please rate.
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: