02-09-2009 12:36 PM - edited 03-06-2019 03:56 AM
HI,
We have two cisco 6500 switch and i need to run HSRP for redunancy between the switch
but my query is since we have lot of VLAN created in primary switch how i can deploy the HSRP between them
whether i need to have different HSRP group for each VLAN
And if i connect the uplink from two catalyst to the distribution switch then whether i need to consider for STP
please suggest me
02-09-2009 12:47 PM
I had two 6500 series with multiple VLANs running HSRP. I had setup HSRP for each VLANs. I also used STP since you will be setting redundant links between your core switches (C6500) to the access layer switches.
02-09-2009 12:50 PM
HI
thanks for the reply
can u post me the sample config which you have deployed since iam new to HSRP and STP
Thanks in advance
Regards
02-09-2009 12:52 PM
I will shortly.
Regards,
02-09-2009 12:56 PM
Thanks
awaiting for your reply
02-09-2009 01:08 PM
Here is just a sample config that i just wrote:
Core1
spanning-tree mode pvst
spanning-tree portfast bpduguard default
spanning-tree portfast bpdufilter default
spanning-tree backbonefast
spanning-tree vlan 30,40 priority 24576
!
!
interface Vlan30
ip address 10.20.30.2 255.255.255.0
ip helper-address 10.20.10.29
no ip route-cache
standby name Servers
standby 30 ip 10.20.30.1
standby 30 priority 110
standby 30 preempt
!
interface Vlan40
ip address 10.20.40.2 255.255.255.0
ip helper-address 10.20.10.29
no ip route-cache
standby name Workstations
standby 40 ip 10.20.40.1
standby 40 priority 110
standby 40 preempt
!
====================================================================================
Core 2
spanning-tree mode pvst
spanning-tree portfast bpduguard default
spanning-tree portfast bpdufilter default
spanning-tree backbonefast
spanning-tree vlan 30,40 priority 28672
!
!
interface Vlan30
ip address 10.20.30.3 255.255.255.0
ip helper-address 10.20.10.29
no ip route-cache
standby name Servers
standby 30 ip 10.20.30.1
standby 30 priority
standby 30 preempt
!
interface Vlan40
ip address 10.20.40.3 255.255.255.0
ip helper-address 10.20.10.29
no ip route-cache
standby name Workstations
standby 40 ip 10.20.40.1
standby 40 priority
standby 40 preempt
===================================================
I also used uplinkfast on the access layer switches:
spanning-tree mode pvst
spanning-tree portfast default
spanning-tree portfast bpduguard default
spanning-tree portfast bpdufilter default
spanning-tree uplinkfast
spanning-tree backbonefast
Regards,
take a look at this link as well
http://www.cisco.com/en/US/tech/tk389/tk621/technologies_configuration_example09186a008009467c.shtml
02-09-2009 02:17 PM
Hi,
Was the above helpful in any way? Please rate as this helps the forum as well.
Regards,
02-10-2009 04:31 AM
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide