02-10-2009 11:52 PM - edited 03-15-2019 04:08 PM
we are configuring a new voice gateway - 2811.
The vg will act as a CCME with E1 connectivity. I am using a VWIC2-1MFT-G703 for E1 connectivity.
E1 controller is up, but when I make a call it gives busy tone. Pls help check whether the config is OK.
The following is the config,
voice translation-rule 1
rule 1 /^0/ //
!
voice translation-rule 10
rule 1 /^21/ //
!
voice translation-profile EnviaNumeroCompleto
translate calling 10
!
voice translation-profile tira0
translate calling 10
translate called 1
!
!
controller E1 0/0/0
framing NO-CRC4
ds0-group 1 timeslots 1-15 type r2-digital r2-compelled ani
cas-custom 1
country brazil use-defaults
metering
category 2
answer-signal group-b 1
!
interface Loopback0
ip address 115.31.255.201 255.255.255.255
!
interface FastEthernet0/0
no ip address
duplex auto
speed auto
!
interface FastEthernet0/0.1
description -SRV-
encapsulation dot1Q 1 native
ip address 192.168.101.1 255.255.255.192
!
interface FastEthernet0/0.2
description -- User --
encapsulation dot1Q 2
ip address 192.168.101.65 255.255.255.192
!
interface FastEthernet0/0.3
description --Voice--
encapsulation dot1Q 3
ip address 192.168.101.129 255.255.255.192
!
interface Service-Engine0/0
ip unnumbered FastEthernet0/0.1
service-module ip address 192.168.101.5 255.255.255.192
service-module ip default-gateway 192.168.101.1
!
interface FastEthernet0/1
description -Telefonica 00HQPROSA00201--
ip address 115.31.250.106 255.255.255.252
duplex full
speed 100
no cdp enable
!
interface Serial0/1/0
description --00HQPROSA00201--
no ip address
clock rate 2000000
!
!
!
voice-port 0/0/0:1
translation-profile outgoing EnviaNumeroCompleto
!
dial-peer voice 5 pots
translation-profile outgoing tira0
destination-pattern 0T
port 0/0/0:1
forward-digits all
!
dial-peer voice 1 pots
destination-pattern .
direct-inward-dial
!
dial-peer voice 503 voip
destination-pattern 6603
session target ipv4:192.168.140.97
dtmf-relay h245-alphanumeric
codec g729r8 bytes 30
!
telephony-service
no auto-reg-ephone
max-ephones 42
max-dn 42
ip source-address 192.168.101.129 port 2000
auto assign 1 to 20
calling-number initiator
timeouts interdigit 3
timeouts busy 20
system message PROSAFE RIO
url services http://192.168.101.5/voiceview/common/login.do
url authentication http://192.168.101.5/voiceview/authentication/authenticate.do
time-zone 17
time-format 24
date-format dd-mm-yy
dialplan-pattern 1 2130436... extension-length 4
voicemail 2999
max-conferences 8 gain -6
call-forward pattern .T
moh music-on-hold.au
web admin system name admin password password
web admin customer name prosafe password prosafe
dn-webedit
time-webedit
transfer-system full-consult
transfer-pattern 8...
transfer-pattern 6...
transfer-pattern 1...
transfer-pattern .T
transfer-pattern 09T
transfer-pattern 08T
transfer-pattern 07T
transfer-pattern 02T
secondary-dialtone 0
after-hours block pattern 1 0 7-24
create cnf-files version-stamp 7960 Feb 06 2009 17:15:40
!
02-11-2009 05:43 AM
Ola',
Begin checking "show controllers E1".
In that regard you nedd "network-clock-participate" and "network-clock-select", check that you have them.
If still problem take "debug vpm signal" with "term mon".
Unrelated to all this, note the -G703 part is wasted money for voice connections, it's necessary only with unframed data circuits.
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: