dsp resources

Unanswered Question
Feb 16th, 2009
User Badges:

Hi there !


I'm having a problem with dspfarm.. the router in using only the PVDM2-64 and PVDM2-32 ... those are onboard pvdm's


How can I start using the PVDM-12 cards that are in NM-HDV?


=================================================

Router Configurations

=================================================

! Onboard

voice-card 0

no dspfarm

dsp services dspfarm

!

! NM-HDV

voice-card 1

no dspfarm

!

! ERROR when I tryied to configure DSP resource

!

(config)#voice-card 1

(config-voicecard)#dsp services dspfarm

dspfarm is configured for NM-HDV2 card.

Only one dspfarm type is allowed.

!

!

sccp ccm group 988

associate profile 6 register XCODE1234

...

!

dspfarm profile 6 transcode

codec g711ulaw

codec g729r8

codec g729br8

codec g711alaw

codec g729abr8

codec g729ar8

maximum sessions 8

associate application SCCP

!

!

=================================================

show inventory

=================================================


NAME: "2821 chassis", DESCR: "2821 chassis"

PID: CISCO2821 , VID: V03 , SN: FTX1038A5QD


NAME: "Two port E1 voice interface daughtercard on Slot 0 SubSlot 0", DESCR: "Two port E1 voice interface daughtercard"

PID: VWIC-2MFT-E1= , VID: 1.0, SN: 34840061


NAME: "PVDMII DSP SIMM with Two DSPs on Slot 0 SubSlot 4", DESCR: "PVDMII DSP SIMM with Two DSPs"

PID: PVDM2-32 , VID: V01 , SN: FOC10301UQX


NAME: "PVDMII DSP SIMM with four DSPs on Slot 0 SubSlot 5", DESCR: "PVDMII DSP SIMM with four DSPs"

PID: PVDM2-64 , VID: V01 , SN: FOC1038277V


NAME: "High Density Voice on Slot 1", DESCR: "High Density Voice"

PID: NM-HDV= , VID: 1.1, SN: JAE07361AED


NAME: "E1 (2 Port) Multi-Flex Trunk (Drop&Insert) WAN Daughter Card on Slot 1 SubSlot 0", DESCR: "E1 (2 Port) Multi-Flex Trunk (Drop&Insert) WAN Daughter Card"

PID: VWIC-2MFT-E1-DI= , VID: 1.0, SN: 30888188


NAME: "PVDM 3-C549 Simm on Slot 1 SubSlot 1", DESCR: "PVDM 3-C549 Simm"

PID: PVDM-12= , VID: 1.1, SN:


NAME: "PVDM 3-C549 Simm on Slot 1 SubSlot 2", DESCR: "PVDM 3-C549 Simm"

PID: PVDM-12= , VID: 1.1, SN:


NAME: "PVDM 3-C549 Simm on Slot 1 SubSlot 3", DESCR: "PVDM 3-C549 Simm"

PID: PVDM-12= , VID: 1.1, SN:


NAME: "PVDM 3-C549 Simm on Slot 1 SubSlot 4", DESCR: "PVDM 3-C549 Simm"

PID: PVDM-12= , VID: 1.1, SN:


NAME: "PVDM 3-C549 Simm on Slot 1 SubSlot 5", DESCR: "PVDM 3-C549 Simm"

PID: PVDM-12= , VID: 1.1, SN:


Thanks.

Andrei.

  • 1
  • 2
  • 3
  • 4
  • 5
Overall Rating: 5 (1 ratings)
Loading.
Chris Deren Mon, 02/16/2009 - 13:51
User Badges:
  • Super Silver, 17500 points or more
  • Hall of Fame,
  • Cisco Designated VIP,

    2017 IP Telephony, Contact Center, Unified Communications

Enter


voice-card 1

dspfarm


HTH,


Chris

Marwan ALshawi Mon, 02/16/2009 - 17:59
User Badges:
  • Purple, 4500 points or more
  • Community Spotlight Award,

    Best Publication, December 2015

wit hDsp there is tow baisic commands

first you need to enable the dsp on the voice port


with dsp farm command in you case on both voice-card 0 and 1


voice-card 0

voice-card 0

dspfarm


no win your router you have a dsp chip on you r mainboard which is 0 and other one in card 1


u can share the DSP resource from the one on mainboard by issueing the following command


voice-card 0

dsp services dspfarm


u need ur voice card look like


voice-card 0

dspfarm

dsp services dspfarm



voice-card

dspfarm


use show voice dsp for troubleshooting as well


good luck

hope this helps


Chris Deren Mon, 02/16/2009 - 18:06
User Badges:
  • Super Silver, 17500 points or more
  • Hall of Fame,
  • Cisco Designated VIP,

    2017 IP Telephony, Contact Center, Unified Communications

Actually, in order to share the PVDMs from different NMs all you need is dspfarm command under the voice-card as I stated earlier, dsp services depfarm allows you to configure the PVDMs for media sharing i.e. conferencing. These 2 get confused by folks all the time, but they have their own specific functions.


Chris

pauleversonCFH Thu, 11/03/2011 - 09:07
User Badges:

Hi,


I have just stumbled across this post.


Did you ever get this working?


I am struggling to get a HM-HDV with 5 x PVDM-12's to join a dspfarm that currently contains 4 x PVDM2-64's


Should this work?

andrei.goncalves Thu, 11/03/2011 - 10:12
User Badges:

Wow.... that’s a 2003 question.... I don’t remember if I solved that or how… sorry..


Now I have another voice gateway (2911 with lots of PVDM’s…)


Andrei.


De: pauleversonCFH

Enviada em: quinta-feira, 3 de novembro de 2011 14:08

Para: Andrei Goncalves

Assunto: - Re: dsp resources


Home


Re: dsp resources

created by Paul Everson in IP Telephony - View the full discussion

Actions

This Discussion