what does sh controller T1 command shows

Answered Question
Feb 17th, 2009

Hi all i have this info

#sh controller t1

, 0 Line Code

T1 4/0/4 is up.

Applique type is Channelized T1

Cablelength is long gain36 0db

Description: P2P T1 to E&P Aztec, NM (nmaztr1 S0/0/0) UCN #DS1-10663022

No alarms detected.

alarm-trigger is not set

Framing is ESF, Line Code is B8ZS, Clock Source is Internal.

Data in current interval (2 seconds elapsed):

0 Line Code Violations, 0 Path Code Violations

0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins

0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs

Total Data (last 86 15 minute intervals):

0 Line Code Violations, 0 Path Code Violations,

0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins,

0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs

T1 4/0/5 is up.

Applique type is Channelized T1

Cablelength is long gain36 0db

Description: T1 to Quailey Peak (W0B-57107)

No alarms detected.

alarm-trigger is not set

Framing is ESF, Line Code is B8ZS, Clock Source is Line.

Data in current interval (2 seconds elapsed):

0 Line Code Violations, 0 Path Code Violations

0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins

0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs

Total Data (last 86 15 minute intervals):

0 Line Code Violations, 0 Path Code Violations,

0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins,

0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs

T1 4/0/6 is up.

Applique type is Channelized T1

Cablelength is long gain36 0db

Description: T1 to Geismar, LA WorldCom # W0N-23488

No alarms detected.

alarm-trigger is not set

Framing is ESF, Line Code is B8ZS, Clock Source is Line.

Data in current interval (2 seconds elapsed):

0 Line Code Violations, 0 Path Code Violations

0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins

0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs

Total Data (last 86 15 minute intervals):

0 Line Code Violations, 1 Path Code Violations,

0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins,

1 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs

T1 4/0/7 is up.

Applique type is Channelized T1

Cablelength is long gain36 0db

Description: T1 to Geismar, LA Verizon Circuit ID: W0S-98733

No alarms detected.

alarm-trigger is not set

Framing is ESF, Line Code is B8ZS, Clock Source is Line.

Data in current interval (2 seconds elapsed):

0 Line Code Violations, 0 Path Code Violations

0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins

0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs

Total Data (last 86 15 minute intervals):

0 Line Code Violations, 22 Path Code Violations,

0 Slip Secs, 4 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins,

14 Errored Secs, 6 Bursty Err Secs, 4 Severely Err Secs, 12 Unavail Secs

i this command for example 3/1/1 means

module/bay /slot--

my understanding is module 3 which is big

device and bay is card inside that has 8

slots or ports

is there any site where i can see the image of this Flexwan controller card

I have this problem too.
0 votes
Correct Answer by Richard Burts about 7 years 11 months ago

Mahesh

This link has a picture of the flexwan card:

http://www.cisco.com/en/US/docs/interfaces_modules/port_adapters/install_upgrade/multichannel_serial/8-port_multichannel_t1.ei_8pri_install_config/2738ovr.html#wp1050186

and earlier in the article it has a picture of the 8 port T1 which can be used in the flexwan card.

HTH

Rick

  • 1
  • 2
  • 3
  • 4
  • 5
Overall Rating: 5 (1 ratings)
Loading.

Actions

This Discussion