cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
572
Views
0
Helpful
7
Replies

MGCP Gateway / On E1 qsig => Somes channels out-of-Service

Hi,

I have CCM in release 4.2

On E1 qsig link between a CISCO 2851 and IP PBX ALCATEL, some ITs goes out-of service.

I only seen this status in RTMT (see in screen shoot in attach)

Do you kwon why this channel goes in out-of service status??

When I make a shut/ no shut, all channel is anew in service.

Regards

Sébastien

7 Replies 7

paolo bevilacqua
Hall of Fame
Hall of Fame

Which exact IOS are you using ?

I'm in c2800nm-ipvoicek9-mz.124-9.T3.bin

Can you try either 12.4(3j), or if need 12.4T features, 12.4(9)T7.

Also please post show controllers E1.

Please found below the sh controller E1

I have the problem on this to links

E1 0/0/0 is up.

Applique type is Channelized E1 - balanced

No alarms detected.

alarm-trigger is not set

Version info Firmware: 20060623, FPGA: 20, spm_count = 0

Framing is NO-CRC4, Line Code is HDB3, Clock Source is Line.

CRC Threshold is 320. Reported from firmware is 320.

Data in current interval (494 seconds elapsed):

0 Line Code Violations, 0 Path Code Violations

0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins

0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs

Total Data (last 24 hours)

0 Line Code Violations, 3748 Path Code Violations,

0 Slip Secs, 2 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins,

0 Errored Secs, 0 Bursty Err Secs, 3 Severely Err Secs, 25 Unavail Secs

E1 0/0/1 is up.

Applique type is Channelized E1 - balanced

No alarms detected.

alarm-trigger is not set

Version info Firmware: 20060623, FPGA: 20, spm_count = 0

Framing is NO-CRC4, Line Code is HDB3, Clock Source is Line.

CRC Threshold is 320. Reported from firmware is 320.

Data in current interval (501 seconds elapsed):

0 Line Code Violations, 0 Path Code Violations

0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins

0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs

Total Data (last 24 hours)

0 Line Code Violations, 0 Path Code Violations,

0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins,

0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 116 Unavail Secs

E1 0/0/0 had got some errors, are you sure the PBX supplies clock on this circuit ?

Hi

We have expeted some problem yesterday at the same time.

In the new « sh controller E1 », there is no new error.

ISRROTONDE1#sh controller E1

E1 0/0/0 is up.

Applique type is Channelized E1 - balanced

No alarms detected.

alarm-trigger is not set

Version info Firmware: 20060623, FPGA: 20, spm_count = 0

Framing is NO-CRC4, Line Code is HDB3, Clock Source is Line.

CRC Threshold is 320. Reported from firmware is 320.

Data in current interval (405 seconds elapsed):

0 Line Code Violations, 0 Path Code Violations

0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins

0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs

Total Data (last 24 hours)

0 Line Code Violations, 0 Path Code Violations,

0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins,

0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 12 Unavail Secs

E1 0/0/1 is up.

Applique type is Channelized E1 - balanced

No alarms detected.

alarm-trigger is not set

Version info Firmware: 20060623, FPGA: 20, spm_count = 0

Framing is NO-CRC4, Line Code is HDB3, Clock Source is Line.

CRC Threshold is 320. Reported from firmware is 320.

Data in current interval (409 seconds elapsed):

0 Line Code Violations, 0 Path Code Violations

0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins

0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs

Total Data (last 24 hours)

0 Line Code Violations, 0 Path Code Violations,

0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins,

0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 60 Unavail Secs

ISRROTONDE1#

Some errors you still have:

0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 12 Unavail Secs

0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 60 Unavail Secs

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: