cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
888
Views
0
Helpful
3
Replies

AP Association with the controller 4402

nitsg.gupta
Level 1
Level 1

i am facing in AP Association with the controller.

i have added option 60 and option 43 on cisco IOS DHCP server.

option 60 ascii "Cisco AP c1250"

option 43 hex f104c0a80ab1

and it is correct config coz i m getting controller ip address and info on AP.

but getting one error that is "Did not get log server settings from DHCP."

any one has knowledge about it?

if any please help me.

here is the AP output.

Translating "CISCO-LWAPP-CONTROLLER"...domain server (4.2.2.2) [OK]

%LWAPP-3-CLIENTEVENTLOG: Controller address 192.168.10.177 obtained through DHCP

%LWAPP-3-CLIENTEVENTLOG: Did not get log server settings from DHCP.

%LWAPP-3-CLIENTEVENTLOG: Performing DNS resolution for CISCO-LWAPP-CONTROLLER

%LWAPP-3-CLIENTEVENTLOG: Controller address 10.32.32.19 obtained through DNS

3 Replies 3

nitsg.gupta
Level 1
Level 1

now i am getting new problem and here is the output

%LWAPP-5-CHANGED: LWAPP changed state to JOIN

%LWAPP-3-CLIENTERRORLOG: Join Timer: did not recieve join response (controller -

WLC_4402)

%LWAPP-3-CLIENTERRORLOG: Set Transport Address: no more AP manager IP addresses

remain

%LWAPP-3-CLIENTERRORLOG: Join Timer: did not recieve join response (controller -

WLC_4402)

%LWAPP-3-CLIENTERRORLOG: Set Transport Address: no more AP manager IP addresses

remain

%SYS-4-PUPDATECLOCK: Periodic Clock update with ROMMON failed, because size left

in ROMMON (4294967295), size needed (29), error code (-1)

%SYS-5-RELOAD: Reload requested by LWAPP CLIENT. Reload Reason: DID NOT GET JOIN

RESPONSE.

%LWAPP-5-CHANGED: LWAPP changed state to DOWN

IOS Bootloader - Starting system.

Xmodem file system is available.

and AP restarts again & again

plz help me.

Join Timer: did not recieve join response (controller - WLC_4402) <--- How many AP's can your controller handle and how many have joined?

Set Transport Address: no more AP manager IP addresses remain < --- Please check your DHCP scope

What is the model of your AP?

What is the IOS your AP is running?

What is the firmware of your WLC4402?

I just had a similar issue with a COMPLETELY different resolution. Usually when you get errors regarding 'No more AP Manager IP addresses remain' or 'Did not get join response' it means things like:

1. Not allowing SSC

2. Improperly configured AP Policies

3. Wrong time on controller

4. Active interface on ap-manager set to 0 instead of 1 or 2

5. and many others...

Here was my situation: I am setting up a small network with a 4402-25. I wanted to collapse all of my 'wireless' devices onto the same subnet. Without thinking it through, the APs and the wireless clients being on the same subnet resulted in the following layer 3 error:

'Discovery request received on wrong VLAN '253' on interface '1', management VLAN = '0' - in L3 mode, dropping the packet.'

So in my case, you can't have your infrastructure APs on the same subnet as clients on an interface configured on the controller that is not a dynamic ap management interface. IOW, this would not apply to having APs and the ap-manager on the same subnet. It isn't recommended to have the APs and ap-manager on the same subnet, but it is valid.

Hope this helps.

Regards,

Scott

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: