Not enough DSP memory?

Unanswered Question
Feb 25th, 2009
User Badges:

We have now 12 channels but the problem is that we need 16 channels, but when I tried to configure it a message appears saying that we have no enough DSP memory. I tried to remove the ds0-group 0 to configure 16 timeslots but I can not. I have installed a PDVM32 but the problem is still the same...

This is the config in my router:

controller E1 3/0/0

framing NO-CRC4

ds0-group 0 timeslots 1-12 type e&m-wink-start

description INTERCONNECT | 12 channels to PBX SIEMENS

!

Slot 3:

High Density Voice Port adapter

xxxx


HDV SIMMs: Product (FRU) Number: PVDM-12=

SIMM slot 0: PVDM-12 SIMM present.

SIMM slot 1: Empty.

SIMM slot 2: Empty.

SIMM slot 3: Empty.

SIMM slot 4: Empty.


And in:

Slot 0:

PVDM Slot 0:

32-channel (G.711) Voice/Fax PVDMII DSP SIMM PVDM daughter card

Hardware Revision : 4.0

Part Number : 73-8539-05

Board Revision : B0

Deviation Number : 0

Fab Version : 04

PCB Serial Number : FOC112312F5

RMA Test History : 00

RMA Number : 0-0-0-0

RMA History : 00

Processor type : 00

Product (FRU) Number : PVDM2-32

Version Identifier : V01

EEPROM format version 4

EEPROM contents (hex):


PVDM Slot 1:

32-channel (G.711) Voice/Fax PVDMII DSP SIMM PVDM daughter card

Hardware Revision : 4.0

Part Number : 73-8539-05

Board Revision : B0

Deviation Number : 0

Fab Version : 04

PCB Serial Number : FOC11441V4X

RMA Test History : 00

RMA Number : 0-0-0-0

RMA History : 00

Processor type : 00

Product (FRU) Number : PVDM2-32

Version Identifier : V01

EEPROM format version 4

EEPROM contents (hex):


  • 1
  • 2
  • 3
  • 4
  • 5
Overall Rating: 5 (1 ratings)
Loading.
Hythim Ali El Hadad Wed, 02/25/2009 - 04:28
User Badges:
  • Silver, 250 points or more


Hi Hernan,


It is shown from your information that you have PVDM 12 installed and you have i HDV-NM


which have 5 PVDM-SIMM sockets

each pvdm-12 give you the folloiwng:


Runs up to twelve voice calls using a medium complexity CODEC (G.711, G.729a/b, G.726, fax).


Runs up to six voice calls using a high complexity CODEC (G.729, G.728, G.723.1).




And you have only one pvdm-12 installed


Check to see if your router support the 2 PVDM2-32 installed and if you configured them as MTP or conf resources


hernanseijas Wed, 02/25/2009 - 05:34
User Badges:

Thanks for your answer and sorry for my ignorance...but where can I check how to do this configuration?

regards

Nicholas Matthews Wed, 02/25/2009 - 05:37
User Badges:
  • Red, 2250 points or more

Hi Hernan,


If you move the T1 card to one of the HWIC slots on the chassis instead of the NM-HDV card, this will work because you have 2 PVDM2-32s on the motherboard. The NM-HDV only has capability for 12 channels at the moment.


hth,

nick

hernanseijas Wed, 02/25/2009 - 06:08
User Badges:

Thanks for your answer, I have this router:

Slot 0:

C3845 Mother board 1GE(TX,SFP),1GE(TX), integrated VPN and 4W Port adapter, 5 ports

PVDM Slot 0:

32-channel (G.711) Voice/Fax PVDMII DSP SIMM PVDM daughter card

PCB Serial Number : PVDM2-32

Version Identifier : V01

PVDM Slot 1:

32-channel (G.711) Voice/Fax PVDMII DSP SIMM PVDM daughter card

Hardware Revision : 4.0

FOC11441V4X

Product (FRU) Number : PVDM2-32

Version Identifier : V01

WIC Slot 0:

Serial 1T WAN daughter card

Hardware revision 1.0 Board revision J0

Serial number 23614000 WIC-1T=

RMA number 00-00-00

Connector type Wan Module

EEPROM format version 1

EEPROM contents (hex):

WIC Slot 1:

Serial 1T WAN daughter card

Hardware revision 1.0 Board revision J0

Serial number 22168867 Part number 800-01514-01

FRU Part Number WIC-1T=

Test history 0x0 RMA number 00-00-00

Connector type Wan Module

Slot 1:

NM-2FE2W Port adapter, 2 ports

Port adapter is analyzed

EEPROM contents at hardware discovery:

Hardware Revision : 1.0

Top Assy. Part Number : 8

NM-2FE2W=

WIC Slot 0:

Serial 1T WAN daughter card

WIC-1T=

Wan Module

EEPROM contents (hex):

Slot 2:

Mueslix-4T Port adapter, 4 ports

Port adapter is analyzed

Board revision H0

Serial number 22689719 Part number 800-02314-02

FRU Part Number NM-4T=

Test history 0x0 RMA number 00-00-00

EEPROM format version 1

EEPROM contents (hex):

Slot 3:

High Density Voice Port adapter

Port adapter is analyzed

Port adapter insertion time unknown

EEPROM contents at hardware discovery:

Hardware Revision : 1.1

Top Assy. Part Number : NM-HDV=

EEPROM format version 4

EEPROM contents (hex):

HDV SIMMs: Product (FRU) Number: PVDM-12=

SIMM slot 0: PVDM-12 SIMM present.

SIMM slot 1: Empty.

SIMM slot 2: Empty.

SIMM slot 3: Empty.

SIMM slot 4: Empty.


WIC Slot 0:

E1 (1 Port) Multi-Flex Trunk WAN Daughter Card

Hardware revision 1.0 Board revision B0

Serial number 28201726 Part number 800-04475-03

FRU Part Number VWIC-1MFT-E1=

Test history 0x0

HDV firmware: Compiled Fri 19-Nov-04 14:23 by michen

HDV memory size 524280 heap free 193977


Slot 4:

NM-2FE2W_V2 Port adapter, 2 ports

Port adapter is analyzed

Port adapter insertion time unknown

EEPROM contents at hardware discovery:

Hardware Revision : 1.1

Top Assy. Part Number : NM-2FE2W-V2

Version Identifier : V01

WIC Slot 0:

E1 (2 port) Multi-Flex Trunk WAN daughter card

Hardware revision 1.0 Board revision B0

Serial number 34969306 Part number 800-04479-04

FRU Part Number VWIC-2MFT-E1=

Test history 0x0 RMA number 00-00-00

Connector type PCI

WIC Slot 1:

E1 (2 port) Multi-Flex Trunk WAN daughter card

Hardware revision 1.0 Board revision B0

Serial number 34969258 Part number 800-04479-04

FRU Part Number VWIC-2MFT-E1=

Test history

Can I do the change you are saying?


Nicholas Matthews Wed, 02/25/2009 - 06:42
User Badges:
  • Red, 2250 points or more

It looks like you have 2 WIC-T cards on in the HWIC slots, and there are 4 on the 3845. You should be able to move the card.



-nick

Actions

This Discussion