cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
1463
Views
0
Helpful
3
Replies

7609 IOS Upgrade Problem

wasiimcisco
Level 1
Level 1

I have cisco 7609 with two SUP-720, WISM, and ethernet modules. Currently I have IOS s72033_rp-ADVIPSERVICESK9_WAN-M), Version 12.2(33)SRA5,

Because this IOS is not detecting the WISM. I am trying the IOS s72033-adventerprisek9_wan-mz.122-18.SXF15 that i have successfully installed in 6513 catalyst which also include the WISM. But now same IOS for 7609 is not working for me.

I followed the below mention steps.

copy ftp: disk0:

Address or name of remote host [192.168.1.11]?

Source filename [s72033-adventerprisek9_wan-mz.122-18.SXF15.bin]?

Destination filename [s72033-adventerprisek9_wan-mz.122-18.SXF15.bin]?

Accessing ftp://192.168.1.11/s72033-adventerprisek9_wan-mz.122-18.SXF15.bin...

Loading s72033-adventerprisek9_wan-mz.122-18.SXF15.bin !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

[OK - 63477880/4096 bytes]

copy disk0:s72033-adventerprisek9_wan-mz.122-18.SXF15a.bin slavedisk0

boot system flash disk0:s72033-adventerprisek9_wan-mz.122-18.SXF15a.bin

but no luck. The Router 7609 goes to mointor mode after this.

When i verify the IOS it gave me following error

ATCT-BD-ULV02-7609-01#verify di

7609-01#$0:s72033-adventerprisek9_wan-mz.122-18.SXF15.bin

%Filesystem does not support verify operations

Verifying file integrity of disk0:s72033-adventerprisek9_wan-mz.122-18.SXF15.bin

%WARNING: Signature not found in file disk0:s72033-adventerprisek9_wan-mz.122-18.SXF15.bin.

ATCT-BD-ULV02-7609-01#

00:18:34: %SIGNATURE-4-NOT_PRESENT: %WARNING: Signature not found in file disk0:s72033-adventerprisek9_wan-mz.122-18.SXF15.bin.

00:18:34: %SIGNATURE-4-NOT_PRESENT: %WARNING: Signature not found in file disk0:s72033-adventerprisek9_wan-mz.122-18.SXF15.bin.

and even with old image i m not able to write configuration on standby. I m gettin following error.

ATCT-BD-ULV02-7609-01#

00:09:34: %PCMCIAFS-SP-5-DFS_CLOSE_ERR: Error during close of the file s72033-adventerprisek9_wan-mz.122-18.SXF15.bin. Failed to flush the remaining file data.

ATCT-BD-ULV02-7609-01#

*** Illegal Opcode Exception ***

PC = 0x8010dce0, Cause = 0x28, Status Reg = 0x30409003

00:03:32: %PFREDUN-SP-4-BOOTSTRING_INVALID: The bootfile slavesupboot-disk:/s72033-advipservicesk9_wan-mz.122-33.SRA5.bin is not present in standby

00:03:34: %PFINIT-SP-5-CONFIG_SYNC: Sync'ing the startup configuration to the standby Router. [OK]

Please let me what i m missing and which IOS image required for 7609.

Please also let me know that the steps i used for upgrade are right or not.

3 Replies 3

wasiimcisco
Level 1
Level 1

can anybody help me out.

Leo Laohoo
Hall of Fame
Hall of Fame

You copied a file called "s72033-adventerprisek9_wan-mz.122-18.SXF15.bin" from your FTP to Disk0 without a problem.

But you tried to copy "s72033-adventerprisek9_wan-mz.122-18.SXF15a.bin" from Disk0 to SlaveDisk0. Do you have "s72033-adventerprisek9_wan-mz.122-18.SXF15a.bin" in Disk0?

Yasir Ashfaque
Level 1
Level 1

type show disk0: and slavedisk0: or dir disk0: and see if same image is there on both disks, also from rommon try to run the image directly by boot command.. see if it helps

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: