03-12-2009 01:29 AM - edited 03-06-2019 04:32 AM
I am trying to figure out if the old Cat5000 WS-X5403 (3-port Gigabit module) linecard supports Etherchannels. I am unable to test this because the interfaces are in production at this time and need to be migrated.
The chassis has the following specs:
sh module
Mod Slot Ports Module-Type Model Sub Status
--- ---- ----- ------------------------- ------------------- --- --------
1 1 2 100BaseFX MMF Supervisor WS-X5530 yes ok
2 2 2 100BaseFX MMF Supervisor WS-X5530 yes standby
4 4 3 1000BaseX Ethernet WS-X5403 no ok
5 5 24 10/100BaseTX Ethernet WS-X5224 no ok
6 6 24 10/100BaseTX Ethernet WS-X5225R no ok
7 7 24 10/100BaseTX Ethernet WS-X5224 no ok
8 8 12 10/100BaseTX Ethernet WS-X5213A no ok
9 9 24 10/100BaseTX Ethernet WS-X5225R no ok
10 10 12 100BaseFX MM Ethernet WS-X5201 no ok
Mod MAC-Address(es) Hw Fw Sw
--- -------------------------------------- ------ ---------- -----------------
1 00-10-07-26-77-00 to 00-10-07-26-7a-ff 1.8 3.1.2 5.5(11)
2 00-10-07-26-77-00 to 00-10-07-26-7a-ff 1.8 3.1.2 5.5(11)
4 00-01-42-ea-ee-f8 to 00-01-42-ea-ee-fa 1.3 4.5(2) 5.5(11)
5 00-10-7b-07-d1-68 to 00-10-7b-07-d1-7f 1.3 3.1(1) 5.5(11)
6 00-d0-06-a2-81-98 to 00-d0-06-a2-81-af 3.3 4.3(1) 5.5(11)
7 00-10-7b-78-f7-a8 to 00-10-7b-78-f7-bf 1.4 3.1(1) 5.5(11)
8 00-e0-1e-e8-71-1c to 00-e0-1e-e8-71-27 2.1 3.1(1) 5.5(11)
9 00-50-0f-b5-fe-c8 to 00-50-0f-b5-fe-df 3.1 4.3(1) 5.5(11)
10 00-10-7b-62-f7-64 to 00-10-7b-62-f7-6f 3.0 3.1(1) 5.5(11)
All three gigabit interfaces are active on different buses (1=A, 2=B, 3=C)
regards,
Geert
Solved! Go to Solution.
03-12-2009 01:46 AM
Hi
Run the following command against the interfaces :-
show interface
Below is an example, note the section Channel: yes
sh interfaces gigabitEthernet 11/1 capabilities
GigabitEthernet11/1
Model: WS-X6148-GE-TX
Type: 10/100/1000BaseT
Speed: 10,100,1000,auto
Duplex: half,full
Trunk encap. type: 802.1Q
Trunk mode: on,off,desirable,nonegotiate
Channel: yes
Broadcast suppression: none
Flowcontrol: rx-(off,on,desired),tx-(off,on,desired)
Membership: static
Fast Start: yes
QOS scheduling: rx-(1q2t), tx-(1p2q2t)
QOS queueing mode: rx-(cos), tx-(cos)
CoS rewrite: yes
ToS rewrite: yes
Inline power: no
Inline power policing: no
SPAN: source/destination
UDLD yes
Link Debounce: yes
Link Debounce Time: no
Ports on ASIC: 1-24
Remote switch uplink: no
Dot1x: yes
Port-Security: yes
03-12-2009 01:46 AM
Hi
Run the following command against the interfaces :-
show interface
Below is an example, note the section Channel: yes
sh interfaces gigabitEthernet 11/1 capabilities
GigabitEthernet11/1
Model: WS-X6148-GE-TX
Type: 10/100/1000BaseT
Speed: 10,100,1000,auto
Duplex: half,full
Trunk encap. type: 802.1Q
Trunk mode: on,off,desirable,nonegotiate
Channel: yes
Broadcast suppression: none
Flowcontrol: rx-(off,on,desired),tx-(off,on,desired)
Membership: static
Fast Start: yes
QOS scheduling: rx-(1q2t), tx-(1p2q2t)
QOS queueing mode: rx-(cos), tx-(cos)
CoS rewrite: yes
ToS rewrite: yes
Inline power: no
Inline power policing: no
SPAN: source/destination
UDLD yes
Link Debounce: yes
Link Debounce Time: no
Ports on ASIC: 1-24
Remote switch uplink: no
Dot1x: yes
Port-Security: yes
03-12-2009 01:52 AM
Thanks, should have known that...
(ps. its still CatOs, so command is show port capabilities:)
>>sh port capabilities 4/1
Model WS-X5403
Port 4/1
Type 1000-LX/LH
Speed 1000
Duplex full
Trunk encap type 802.1Q,ISL
Trunk mode on,off,desirable,auto,nonegotiate
Channel no
Broadcast suppression percentage(0-100)
Flow control receive-(off,on,desired),send-(off,on,desired)
Security no
Membership static
Fast start yes
QOS scheduling rx-(none),tx-(none)
CoS rewrite no
ToS rewrite no
Rewrite no
UDLD yes
AuxiliaryVlan no
SPAN source,destination
It clearly states: "no". Da**ned. There goes my migration plan :-)
03-12-2009 02:09 AM
I have felt that pain many times, good luck with the new plan.
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: