Outgoing Call Failure

Answered Question
Mar 12th, 2009
User Badges:

I recently upgraded to UCM 7.0 from CM 4.1.3. After the upgrade I have been noticing a various phone numbers are flagged as international when they are processed by the h323 gateway. It seems to be relative to a particular area code. All of these calls that fail are national.


1402035: Mar 12 15:39:08.008 CST: ISDN Se1/0:23 Q931: isdn_parser_map_lkup: overriding plan/type for XXXXXXXXXX, isdn/national to isdn/international

1402036: Mar 12 15:39:08.012 CST: ISDN Se1/0:23 Q931: isdn_parser_map_lkup: overriding plan/type for XXXXXXXXXX, isdn/national to isdn/international

1402037: Mar 12 15:39:08.020 CST: ISDN Se1/0:23 Q931: TX -> SETUP pd = 8 callref = 0x744C

Bearer Capability i = 0x8090A2

Standard = CCITT

Transer Capability = Speech

Transfer Mode = Circuit

Transfer Rate = 64 kbit/s

Channel ID i = 0xE9818398

Exclusive, Interface 1, Channel 24

Calling Party Number i = 0x2181, 'XXXXXXXXXX'

Plan:ISDN, Type:National

Called Party Number i = 0x91, 'XXXXXXXXXX'

Plan:ISDN, Type:International

1402038: Mar 12 15:39:08.068 CST: ISDN Se1/0:23 Q931: RX <- RELEASE_COMP pd = 8 callref = 0xF44C



Correct Answer by gogasca about 8 years 2 weeks ago

1402035: Mar 12 15:39:08.008 CST: ISDN Se1/0:23 Q931: isdn_parser_map_lkup: overriding plan/type for XXXXXXXXXX, isdn/national to isdn/international

1402036: Mar 12 15:39:08.012 CST: ISDN Se1/0:23 Q931: isdn_parser_map_lkup: overriding plan/type for XXXXXXXXXX, isdn/national to isdn/international



do u have a rule defined in the serial interface for this T1 PRI?

like isdn map ?


http://www.cisco.com/en/US/docs/ios/12_3t/dial/command/reference/dia_i2gt.html#wp1212108

  • 1
  • 2
  • 3
  • 4
  • 5
Overall Rating: 5 (1 ratings)
Loading.
Correct Answer
gogasca Thu, 03/12/2009 - 23:09
User Badges:
  • Green, 3000 points or more

1402035: Mar 12 15:39:08.008 CST: ISDN Se1/0:23 Q931: isdn_parser_map_lkup: overriding plan/type for XXXXXXXXXX, isdn/national to isdn/international

1402036: Mar 12 15:39:08.012 CST: ISDN Se1/0:23 Q931: isdn_parser_map_lkup: overriding plan/type for XXXXXXXXXX, isdn/national to isdn/international



do u have a rule defined in the serial interface for this T1 PRI?

like isdn map ?


http://www.cisco.com/en/US/docs/ios/12_3t/dial/command/reference/dia_i2gt.html#wp1212108

joel.salminen Fri, 03/13/2009 - 07:35
User Badges:

Thanks for the information. It does work to force the isdn type to national. Any idea why this particular area code gets flagged as international? Here's my serial config:


interface Serial1/0:23

no ip address

no logging event link-status

isdn switch-type primary-4ess

isdn incoming-voice voice

isdn map address 011* plan isdn type international

isdn map address 770* plan isdn type national

no isdn outgoing ie redirecting-number

no isdn incoming alerting add-PI

isdn nsf-service megacom

no cdp enable

Actions

This Discussion