03-13-2009 05:42 AM - edited 03-04-2019 03:55 AM
I configured Tunnel, but i am not able to ping my remote tunnel ip.ie 10.10.1.2 and vice-versa.
On Mumbai Router
inter fa 0/0
ip address 10.5.2.2 255.255.255.252
des "connected to WAN"
inter tunnel 0
ip address 10.10.1.1 255.255.255.252
tunnel source 10.5.2.2
tunnel destination 10.5.2.90
ip route 10.10.1.0 255.255.255.252 10.5.2.1
On Pune Router
inter fa 0/0
ip address 10.5.2.90 255.255.255.252
des "connected to WAN"
inter tunnel 0
ip address 10.10.1.2 255.255.255.252
tunnel source 10.5.2.89
tunnel destination 10.5.2.2
ip route 10.10.1.0 255.255.255.252 10.5.2.89
03-13-2009 06:04 AM
Arjun,
The source address of the tunnel interface on Pune should be the fa0/0 address 10.5.2.90 rather than 10.5.2.89.
Do you have a route on Mumbai to reach 10.5.2.90 ans inversely a route on Pune to reach 10.5.2.2.
Also, you do not need the static routes for 10.10.1.0/30 as these routes will be installed as a connected routes because of the tunnel interface.
Regards
03-15-2009 12:40 AM
Thanx...
I'll Try and revert.
03-15-2009 08:51 PM
Thanx a Lot..
Now i am able to ping my remote tunnel IP.I have one more query.
I have one more backup ISP to Pune using BGP.I want redundancy.If my 1st ISP fail, 2nd will work.
can I create a second tunnel for that.
Currently for 1st ISP i am using static route.Is it possible to use same loopback address for both ISP.
I am very greatful to U.
03-17-2009 05:17 AM
Hi..
Any suggestion..
03-17-2009 06:05 AM
Arjun,
Could you please explain why you would need a GRE tunnel to your primary or backup ISP.
Regards
03-18-2009 04:34 AM
Thanx...
I need autofailover to my both ISP.
Pune user should access Mumbai via 2nd ISP if my 1st ISP fail.
Thax Again..
03-18-2009 05:57 AM
Arjun,
And why do you need GRE tunnels to do that? Can't you do it without GRE? A diagram might be useful.
Regards
03-19-2009 04:57 AM
Thanx a lot..
I can do this without GRE.
My priority is Autofailover to my both ISP.For REL(MPLS VPN) i am using BGP and for VSNL (MPLS VPN) using static routes on my Mumbai router.
On Pune router i am using static routes for primary (REL).When REL down i manually change that routes toward VSNL.
Is there any way to autoswitchover route like using metric.
Pls find the attachment.
03-19-2009 07:34 AM
You can use conditional advertisemsnt on the router that is running BGP. Please check out "neighbor advertise-map non-exist-map"
http://www.cisco.com/en/US/docs/ios/12_1/iproute/command/reference/1rdbgp.html#wp1150201
03-19-2009 08:26 PM
Thax for u'r suggestion..
But on pune router i am not using BGP.There is a static route for ISP.
Is there any way..?
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: