CME 4.0 Unable to make out going calls neither i can receive in coming call

Unanswered Question
Mar 17th, 2009

Hi Guys

I have configred 2811 router with CME 4.0, the ip phones are configured properly but the problem is with incoming and outgoing calls, when ever i try to make a call, after dialing the complete number i get an engage tone, same thing is happening with the incoming, the incoming call is not landing on the configured ip phone below are the voice ports and dial peer configuration

voice-port 0/1/0

trunk-group FXOPORTS

supervisory disconnect dualtone mid-call

supervisory custom-cptone UAE-CUSTOM-SIEMENS

supervisory dualtone-detect-params 1

timeouts call-disconnect 5

connection plar opx 418

caller-id enable

--More-- !

voice-port 0/1/1

trunk-group FXOPORTS

supervisory disconnect dualtone mid-call

supervisory custom-cptone UAE-CUSTOM-SIEMENS

supervisory dualtone-detect-params 1

timeouts call-disconnect 5

connection plar opx 418

caller-id enable

!

voice-port 0/1/2

trunk-group FXOPORTS

supervisory disconnect dualtone mid-call

supervisory custom-cptone UAE-CUSTOM-SIEMENS

supervisory dualtone-detect-params 1

timeouts call-disconnect 5

connection plar opx 418

caller-id enable

!

voice-port 0/1/3

trunk-group FXOPORTS

supervisory disconnect dualtone mid-call

supervisory custom-cptone UAE-CUSTOM-SIEMENS

--More-- supervisory dualtone-detect-params 1

timeouts call-disconnect 5

connection plar opx 418

caller-id enable

!

!

!

!

!

dial-peer voice 203 pots

trunkgroup FXOPORTS

description *** Mobile Dial-Peer ***

destination-pattern 905[056].......$

prefix 05

!

dial-peer voice 215 pots

trunkgroup FXOPORTS

description *** TollFree Dial-Peer ***

destination-pattern 9800T

prefix 800

--More-- !

dial-peer voice 206 pots

trunkgroup FXOPORTS

description *** National Dial-Peer ***

destination-pattern 90[1-4,6-9].......$

prefix 0

!

dial-peer voice 204 pots

trunkgroup FXOPORTS

description *** Landline Dial-Peer ***

destination-pattern 9[2345789]......$

!

dial-peer voice 202 pots

trunkgroup FXOPORTS

description *** Emergency Dial-Peer ***

preference 7

destination-pattern 9[19]..$

prefix 6

A quick reply will be highly appreciated.

Cheers

Aamir

I have this problem too.
0 votes
  • 1
  • 2
  • 3
  • 4
  • 5
Overall Rating: 0 (0 ratings)
Loading.
aamirdhedhi Wed, 03/18/2009 - 23:13

yes the lines have been tested on the regular telephone, there is one thing that i have noticed below is the description when i use the command

(show dial-peer voice)

(Time elapsed since last clearing of voice call statistics never

Connect Time = 0, Charged Units = 0,

Successful Calls = 0, Failed Calls = 16, Incomplete Calls = 0

Accepted Calls = 0, Refused Calls = 0,

Last Disconnect Cause is "22 ",

Last Disconnect Text is "no circuit (34)",

Last Setup Time = 16014477.)

I already have a running setup with the same hardware and configuration in our other location which is working stable, the out put of the (Show dial-peer voice) is as follows

(Time elapsed since last clearing of voice call statistics never

Connect Time = 1170159, Charged Units = 0,

Successful Calls = 128, Failed Calls = 0, Incomplete Calls = 0

Accepted Calls = 0, Refused Calls = 0,

Last Disconnect Cause is "10 ",

Last Disconnect Text is "normal call clearing (16)",

Last Setup Time = 82279145.

Last Disconnect Time = 82294945.)

The difference is the last disconnect cause and the last disconnect text.

Please reply thanks for your support

Cheers

Aamir

Paolo Bevilacqua Wed, 03/18/2009 - 23:15

Need to see the debug vpm output. Might be a battery denial issue requiring some configuration under voice-port.

Paolo Bevilacqua Thu, 03/19/2009 - 09:16

Hi, have the lines checked again, router detects power denial, might be a low line voltage, etc. Sometime, swapping tip and ring wires helps.

Actions

This Discussion