03-19-2009 12:13 PM - edited 03-11-2019 08:07 AM
I am having simple issue with setting up port forwarding for RDC on ASA 5505. I have configured several other ASA 5505 appliances using the same commands and they all work fine. Here is the running config. Any help would be appreciated.
Result of the command: "show conf"
: Saved
: Written by enable_15 at 05:11:58.270 UTC Thu Mar 19 2009
!
ASA Version 7.2(2)
!
hostname ciscoasa
domain-name default.domain.invalid
enable password xxxx encrypted
names
!
interface Vlan1
nameif inside
security-level 100
ip address 192.168.3.1 255.255.255.0
!
interface Vlan2
nameif outside
security-level 0
ip address 70.x.x.x 255.255.255.248
!
interface Ethernet0/0
switchport access vlan 2
!
interface Ethernet0/1
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
!
interface Ethernet0/5
!
interface Ethernet0/6
!
interface Ethernet0/7
!
passwd xxxx encrypted
ftp mode passive
dns server-group DefaultDNS
domain-name default.domain.invalid
access-list outside_access_in_web extended permit tcp any interface outside eq 3389
pager lines 24
logging asdm informational
mtu outside 1500
mtu inside 1500
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-522.bin
no asdm history enable
arp timeout 14400
global (outside) 1 interface
nat (inside) 1 0.0.0.0 0.0.0.0
static (inside,outside) tcp interface 3389 192.168.3.48 3389 netmask 255.255.255.255
access-group outside_access_in_web in interface outside
route outside 0.0.0.0 0.0.0.0 70.x.x.x 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout uauth 0:05:00 absolute
http server enable
http 192.168.3.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
telnet timeout 5
ssh timeout 5
console timeout 0
dhcpd auto_config outside
!
dhcpd address 192.168.3.2-192.168.3.129 inside
dhcpd enable inside
!
!
class-map inspection_default
match default-inspection-traffic
!
!
policy-map type inspect dns preset_dns_map
parameters
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
!
service-policy global_policy global
prompt hostname context
Cryptochecksum:7574d93ff465f1714247a73fa3b2d265
03-19-2009 12:48 PM
Hi Almir,
Your ACL and NAT statements both look good to me. Try adding:
ASA(config)# interface e0/x
ASA(config-if)# switchport access vlan 1
Where e0/x is the interface that the RDP server (192.168.3.48) is connected to (e.g. e0/1). This will configure the switch port as an access port for VLAN 1 (your inside network).
Hope that helps.
-Mike
03-23-2009 10:05 AM
config looks fine
Does RDP work locally?
If you access the rdp server from outside, do you get hit counts in your outside ACL?
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: