IOS issue with the Cisco 7206

Unanswered Question
Mar 20th, 2009

Hi,

We are using the router 7206 VXR NPGE2 with the version

bootstrap version 12.4 (12.2r)T,release software FC1

System image file "bootflash:c7200p-k91p-mz.122-31.SB10.bin

which is doesnt support NAT so we need the latest support version for the router

can any one advice

Regards,

Vinu

I have this problem too.
0 votes
  • 1
  • 2
  • 3
  • 4
  • 5
Overall Rating: 5 (1 ratings)
Loading.
vinoth.kumar Fri, 03/20/2009 - 09:20

i tried upload the image in disk2 and in the Rmon i given

Rmon> boot disk2: c7200p-spservicesk9-mz.124-15.T8.bin

after reset i say the error

The message from the bootldr

String is disk2:c7200p-spservicesk9-mz.124-15.T8.bin

loadprog: errorr -invalid image for this platform

CPU type = 169

boot = cannot find an excutable image for ths platform on device slot 1

Regards,

Vinu

Edison Ortiz Fri, 03/20/2009 - 09:25

That's odd. That image is supposed to work on NPE-G2.

Please boot with the other image and paste the output from show diag and show ver

__

Edison.

vinoth.kumar Sat, 03/28/2009 - 10:44

Hi,

please find the output of the two commands

Router#sh version

Cisco IOS Software, 7200 Software (C7200P-K91P-M), Version 12.2(31)SB10, RELEASE SOFTWARE (fc2)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2007 by Cisco Systems, Inc.

Compiled Fri 16-Nov-07 04:08 by richv

ROM: System Bootstrap, Version 12.4(12.2r)T, RELEASE SOFTWARE (fc1)

Router uptime is 1 minute

System returned to ROM by power-on

System image file is "bootflash:c7200p-k91p-mz.122-31.SB10.bin"

This product contains cryptographic features and is subject to United

States and local country laws governing import, export, transfer and

use. Delivery of Cisco cryptographic products does not imply

third-party authority to import, export, distribute or use encryption.

Importers, exporters, distributors and users are responsible for

compliance with U.S. and local country laws. By using this product you

agree to comply with applicable laws and regulations. If you are unable

to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:

http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to

[email protected].

Cisco 7206VXR (NPE-G2) processor (revision A) with 917504K/65536K bytes of memory.

Processor board ID 21268035

MPC7448 CPU at 1666Mhz, Implementation 0, Rev 2.2

6 slot VXR midplane, Version 2.0

Last reset from power-on

PCI bus mb1 (Slots 1, 3 and 5) has a capacity of 600 bandwidth points.

Current configuration on bus mb1 has a total of 400 bandwidth points.

This configuration is within the PCI bus capacity and is supported.

PCI bus mb2 (Slots 2, 4 and 6) has a capacity of 600 bandwidth points.

Current configuration on bus mb2 has a total of 0 bandwidth points.

This configuration is within the PCI bus capacity and is supported.

Please refer to the following document "Cisco 7200 Series Port Adaptor

Hardware Configuration Guidelines" on Cisco.com <http://www.cisco.com>

for c7200 bandwidth points oversubscription and usage guidelines.

3 FastEthernet interfaces

3 Gigabit Ethernet interfaces

2045K bytes of NVRAM.

65536K bytes of Flash internal SIMM (Sector size 512K).

Configuration register is 0x2142

Router#sh diag

Slot 3:

Dual Port FastEthernet (RJ45) Port adapter, 2 ports

Port adapter is analyzed

Port adapter insertion time 00:01:20 ago

EEPROM contents at hardware discovery:

Controller Type : 548

Hardware Revision : 1.1

PCB Serial Number : JAE063007QA

PCB Part Number : 73-5419-07

Board Revision : A0

RMA Test History : 07

RMA Number : 0-0-0-0

RMA History : 00

Deviation Number : 0-0

Product Identifier (PID) : PA-2FE-TX

Top Assy. Part Number : 800-08350-06

EEPROM format version 4

EEPROM contents (hex):

0x00: 04 FF 40 02 24 41 01 01 C1 8B 4A 41 45 30 36 33

0x10: 30 30 37 51 41 82 49 15 2B 07 42 41 30 03 07 81

0x20: 00 00 00 00 04 00 80 00 00 00 00 CB 94 50 41 2D

0x30: 32 46 45 2D 54 58 20 20 20 20 20 20 20 20 20 20

0x40: 20 C0 46 03 20 00 20 9E 06 FF FF FF FF FF FF FF

0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

Router#

Edison Ortiz Sat, 03/28/2009 - 16:14

Did you format the compact flash holding the IOS image?

If not, format the compact flash - copy the image once again onto the flash and try again.

__

Edison.

rpfinneran Sun, 03/29/2009 - 03:23

You cannot have a space between disk2 and the IOS file name, this causes the router to be unable to find the IOS.

"Rmon> boot disk2: c7200p-spservicesk9-mz.124-15.T8.bin"

vinoth.kumar Sun, 03/29/2009 - 17:51

Hi,

When i am trying to copy the image itself it says the message that the image is not excuatble for the platform

Router#copy tftp: disk2:

Address or name of remote host [192.168.1.10]? 192.168.1.10 Source filename [c7200-spservicesk9-mz.124-15.T8.bin]? c7200-spservicesk9-mz.124-15.T8.bin

Destination filename [c7200-spservicesk9-mz.124-15.T8.bin]?

Accessing tftp://192.168.1.10/c7200-spservicesk9-mz.124-15.T8.bin...

%Warning: File not a valid executable for this system

Abort Copy? [confirm]n

Loading c7200-spservicesk9-mz.124-15.T8.bin from 192.168.1.10 (via GigabitEthernet0/1):

Intern of boot from the image it says the error

%SYS-6-BOOT_MESSAGES: Messages above this line are from the boot loader.

loadprog: error - Invalid image for platform

e_machine = 25, cpu_type = 169

boot: cannot load "cisco2-C7200"

Please suggest

Thanks

Vinu

Edison Ortiz Sun, 03/29/2009 - 19:47

Vinu,

You downloaded the image for the NPE-G1, not the image for the NPE-G2. Notice the 'p' missing on the c7200 as part of the filename.

Download the correct image and try again.

__

Edison.

vinoth.kumar Mon, 03/30/2009 - 07:57

Thanks it working now

Is there specific command or any way i can monitor what are configuration changes we are doing

Since suddenly some chnage are happening on our router configuration

Actions

This Discussion