03-20-2009 07:59 AM - edited 03-04-2019 04:01 AM
Hi,
We are using the router 7206 VXR NPGE2 with the version
bootstrap version 12.4 (12.2r)T,release software FC1
System image file "bootflash:c7200p-k91p-mz.122-31.SB10.bin
which is doesnt support NAT so we need the latest support version for the router
can any one advice
Regards,
Vinu
03-20-2009 08:32 AM
Try c7200p-spservicesk9-mz.124-15.T8.bin
__
Edison.
03-20-2009 09:20 AM
i tried upload the image in disk2 and in the Rmon i given
Rmon> boot disk2: c7200p-spservicesk9-mz.124-15.T8.bin
after reset i say the error
The message from the bootldr
String is disk2:c7200p-spservicesk9-mz.124-15.T8.bin
loadprog: errorr -invalid image for this platform
CPU type = 169
boot = cannot find an excutable image for ths platform on device slot 1
Regards,
Vinu
03-20-2009 09:25 AM
That's odd. That image is supposed to work on NPE-G2.
Please boot with the other image and paste the output from show diag and show ver
__
Edison.
03-28-2009 10:44 AM
Hi,
please find the output of the two commands
Router#sh version
Cisco IOS Software, 7200 Software (C7200P-K91P-M), Version 12.2(31)SB10, RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2007 by Cisco Systems, Inc.
Compiled Fri 16-Nov-07 04:08 by richv
ROM: System Bootstrap, Version 12.4(12.2r)T, RELEASE SOFTWARE (fc1)
Router uptime is 1 minute
System returned to ROM by power-on
System image file is "bootflash:c7200p-k91p-mz.122-31.SB10.bin"
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
Cisco 7206VXR (NPE-G2) processor (revision A) with 917504K/65536K bytes of memory.
Processor board ID 21268035
MPC7448 CPU at 1666Mhz, Implementation 0, Rev 2.2
6 slot VXR midplane, Version 2.0
Last reset from power-on
PCI bus mb1 (Slots 1, 3 and 5) has a capacity of 600 bandwidth points.
Current configuration on bus mb1 has a total of 400 bandwidth points.
This configuration is within the PCI bus capacity and is supported.
PCI bus mb2 (Slots 2, 4 and 6) has a capacity of 600 bandwidth points.
Current configuration on bus mb2 has a total of 0 bandwidth points.
This configuration is within the PCI bus capacity and is supported.
Please refer to the following document "Cisco 7200 Series Port Adaptor
Hardware Configuration Guidelines" on Cisco.com <http://www.cisco.com>
for c7200 bandwidth points oversubscription and usage guidelines.
3 FastEthernet interfaces
3 Gigabit Ethernet interfaces
2045K bytes of NVRAM.
65536K bytes of Flash internal SIMM (Sector size 512K).
Configuration register is 0x2142
Router#sh diag
Slot 3:
Dual Port FastEthernet (RJ45) Port adapter, 2 ports
Port adapter is analyzed
Port adapter insertion time 00:01:20 ago
EEPROM contents at hardware discovery:
Controller Type : 548
Hardware Revision : 1.1
PCB Serial Number : JAE063007QA
PCB Part Number : 73-5419-07
Board Revision : A0
RMA Test History : 07
RMA Number : 0-0-0-0
RMA History : 00
Deviation Number : 0-0
Product Identifier (PID) : PA-2FE-TX
Top Assy. Part Number : 800-08350-06
EEPROM format version 4
EEPROM contents (hex):
0x00: 04 FF 40 02 24 41 01 01 C1 8B 4A 41 45 30 36 33
0x10: 30 30 37 51 41 82 49 15 2B 07 42 41 30 03 07 81
0x20: 00 00 00 00 04 00 80 00 00 00 00 CB 94 50 41 2D
0x30: 32 46 45 2D 54 58 20 20 20 20 20 20 20 20 20 20
0x40: 20 C0 46 03 20 00 20 9E 06 FF FF FF FF FF FF FF
0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
Router#
03-28-2009 04:14 PM
Did you format the compact flash holding the IOS image?
If not, format the compact flash - copy the image once again onto the flash and try again.
__
Edison.
03-29-2009 03:23 AM
You cannot have a space between disk2 and the IOS file name, this causes the router to be unable to find the IOS.
"Rmon> boot disk2: c7200p-spservicesk9-mz.124-15.T8.bin"
03-29-2009 05:51 PM
Hi,
When i am trying to copy the image itself it says the message that the image is not excuatble for the platform
Router#copy tftp: disk2:
Address or name of remote host [192.168.1.10]? 192.168.1.10 Source filename [c7200-spservicesk9-mz.124-15.T8.bin]? c7200-spservicesk9-mz.124-15.T8.bin
Destination filename [c7200-spservicesk9-mz.124-15.T8.bin]?
Accessing tftp://192.168.1.10/c7200-spservicesk9-mz.124-15.T8.bin...
%Warning: File not a valid executable for this system
Abort Copy? [confirm]n
Loading c7200-spservicesk9-mz.124-15.T8.bin from 192.168.1.10 (via GigabitEthernet0/1):
Intern of boot from the image it says the error
%SYS-6-BOOT_MESSAGES: Messages above this line are from the boot loader.
loadprog: error - Invalid image for platform
e_machine = 25, cpu_type = 169
boot: cannot load "cisco2-C7200"
Please suggest
Thanks
Vinu
03-29-2009 07:47 PM
Vinu,
You downloaded the image for the NPE-G1, not the image for the NPE-G2. Notice the 'p' missing on the c7200 as part of the filename.
Download the correct image and try again.
__
Edison.
03-30-2009 07:57 AM
Thanks it working now
Is there specific command or any way i can monitor what are configuration changes we are doing
Since suddenly some chnage are happening on our router configuration
03-30-2009 08:05 AM
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: