Cisco 1200 Crashed

Unanswered Question
Mar 25th, 2009

Hello All

My working AP1200 crashed in the bottom I am seeing the lights for radioand ethernet red and status is light purple on the other hand in console mode

I am just seeing

ap:

and possible commands are

? -- Present list of available commands

arp -- Show arp table or arp-resolve an address

boot -- Load and boot an executable image

cat -- Concatenate (type) file(s)

clear_ether -- clear ethernet port statistics

copy -- Copy a file

delete -- Delete file(s)

dir -- List files in directories

dump_save_regs -- dump saved regs in OCM

etest -- test emac driver code

ether_init -- initialize ethernet port

flash_init -- Initialize flash filesystem(s)

format -- Format a filesystem

fsck -- Check filesystem consistency

help -- Present list of available commands

init_pci -- initialize pci bridge

led_test -- cycle led patterns

memory -- Present memory heap utilization information

mkdir -- Create dir(s)

more -- Concatenate (display) file(s)

rename -- Rename a file

reset -- Reset the system

-- MORE --

reset_gpio -- reset gpio

rmdir -- Delete empty dir(s)

set -- Set or display environment variables

set_baud -- set baud rates

set_gpio -- set gpio

set_sleep -- Pause (sleep) for a specified number of seconds

show_ether -- show ethernet port statistics

show_pci -- show pci setting

switch status -- report push button switch status

tar -- extract or listing a tar file

test ram -- read at address

tftp_init -- Initialize tftp file system

type -- Concatenate (type) file(s)

unset -- Unset one or more environment variables

version -- Display boot loader version

But some of them are not working for example Boot

ap: boot

Loading ""...: permission denied

Error loading ""

Interrupt within 5 seconds to abort boot process.

Boot process failed...

ap:

One more thing during reset

The system is unable to boot automatically because there

are no bootable files to boot.

Looks like no IOS on it.I would also like to ask how to put IOS back into the AP

Any idea how to recover it ?

Regards

Ersin

I have this problem too.
0 votes
  • 1
  • 2
  • 3
  • 4
  • 5
Overall Rating: 0 (0 ratings)
Loading.
jeff.kish Wed, 03/25/2009 - 06:37

Hi Ersin,

I actually just went through this process myself. First, run the "dir flash:" command to see if you have anything in flash (this may require the "flash_init" command first). If you have an IOS copy, it may be corrupt and you should delete it before proceeding. If not, proceed away!

Next, run the "ether_init" and "tftp_init" commands. This turns on the Ethernet interface and enables TFTP. You'll next want to use the "set" command to change the IP address. You can change it to anything, really, as long as it can access a TFTP server on your network, or maybe access your PC directly via a cross-over cable.

Next, run the "tar tftp://TFTP_SERVER/FILENAME" command (I think this is right, but you might need to play with the syntax a bit). This will unzip the IOS file directly to flash. This is usually required because the 1200 doesn't have enough flash to store the tar file and unzip it at the same time.

I hope this helps! Let me know if I forgot anything, or if this doesn't work for any reason.

Jeff

ergonullu Wed, 03/25/2009 - 06:52

Bad news...

I copied the file and extract it now

executing...

Xmodem file system is available.

flashfs[0]: 151 files, 7 directories

flashfs[0]: 0 orphaned files, 0 orphaned directories

flashfs[0]: Total bytes: 15998976

flashfs[0]: Bytes used: 4973056

flashfs[0]: Bytes available: 11025920

flashfs[0]: flashfs fsck took 28 seconds.

Base ethernet MAC Address: 00:1d:a1:ff:fb:a2

Initializing ethernet port 0...

Reset ethernet port 0...

Reset done!

ethernet link up, 100 mbps, full-duplex

Ethernet port 0 initialized: link is up

Loading "flash:/c1200-k9w7-mx.123-8.JEA2/c1200-k9w7-mx.123-8.JEA2"...###########

################################################################################

################################################################################

################################################################################

################################################################################

##############

File "flash:/c1200-k9w7-mx.123-8.JEA2/c1200-k9w7-mx.123-8.JEA2" uncompressed and

installed, entry point: 0x3000

executing...

and it hangsç.Break sequence is not workinmg for ap:...how could I get in the ap: during the boot by break

Regards

Ersin

Actions

This Discussion

 

 

Trending Topics: Other Wireless Mobility

client could not be authenticated
Network Analysis Module (NAM) Products
Cisco 6500 nam
reason 440 driver failure
Cisco password cracker
Cisco Wireless mode