IOS

justingorres · ‎04-01-2009

I'm trying to setup a test bed for callmanager 7 and the router I'm using for the network will not recognize any of the voice cards in the running config (as in, no dial-peers or voice ports.) I am running it's default IOS 12.4(3g) SPServices which we are using elsewhere just fine. I issue the "sh ver" command and I see that it recognizes that I have a 4 port FXO, 2-port FXS and a Channelized T1/PRI Controller card plugged in.

Sh Ver:

Cisco 2811 (revision 53.51) with 251904K/10240K bytes of memory.

Processor board ID FTX1233A42P

2 FastEthernet interfaces

1 Serial interface

1 Channelized T1/PRI port

4 Voice FXO interfaces

2 Voice FXS interfaces

DRAM configuration is 64 bits wide with parity enabled.

239K bytes of non-volatile configuration memory.

62720K bytes of ATA CompactFlash (Read/Write)

Any ideas would be greatly appreciated!

Thotsaphon Lueangwattanaphong · ‎04-01-2009

Justin,

Please post a "sh diag" command.

To make sure that you have any PVDM installed on it.

Toshi

justingorres · ‎04-01-2009

Test_Router#sh diag

Slot 0:

C2811 Motherboard with 2FE and integrated VPN Port adapter, 2 ports

Port adapter is analyzed

Port adapter insertion time unknown

EEPROM contents at hardware discovery:

PCB Serial Number : FOC12312FZM

Hardware Revision : 1.0

Top Assy. Part Number : 800-26920-04

Board Revision : A0

Deviation Number : 0

Fab Version : 04

RMA Test History : 00

RMA Number : 0-0-0-0

RMA History : 00

Processor type : 87

Hardware date code : 20080731

Chassis Serial Number : FTX1233A42P

Chassis MAC Address : 0022.904c.9748

MAC Address block size : 24

CLEI Code : COM7R00ARA

Product (FRU) Number : CISCO2811

Part Number : 73-10258-05

Version Identifier : V05

EEPROM format version 4

EEPROM contents (hex):

0x00: 04 FF C1 8B 46 4F 43 31 32 33 31 32 46 5A 4D 40

0x10: 03 E7 41 01 00 C0 46 03 20 00 69 28 04 42 41 30

0x20: 88 00 00 00 00 02 04 03 00 81 00 00 00 00 04 00

0x30: 09 87 83 01 32 68 5B C2 8B 46 54 58 31 32 33 33

0x40: 41 34 32 50 C3 06 00 22 90 4C 97 48 43 00 18 C6

0x50: 8A 43 4F 4D 37 52 30 30 41 52 41 CB 8F 43 49 53

0x60: 43 4F 32 38 31 31 20 20 20 20 20 20 82 49 28 12

0x70: 05 89 56 30 35 20 D9 02 40 C1 FF FF FF FF FF FF

WIC Slot 0:

2nd generation - FXS Voice daughter card (2 port)

Hardware Revision : 3.1

Top Assy. Part Number : 800-21341-01

Board Revision : E0

Deviation Number : 0-0

Fab Version : 01

PCB Serial Number : FOC093352D2

RMA Test History : 00

RMA Number : 0-0-0-0

RMA History : 00

Version Identifier : V

Product (FRU) Number : VIC2-2FXS=

EEPROM format version 4

EEPROM contents (hex):

0x00: 04 FF 40 00 47 41 03 01 C0 46 03 20 00 53 5D 01

0x10: 42 45 30 80 00 00 00 00 02 01 C1 8B 46 4F 43 30

0x20: 39 33 33 35 32 44 32 03 00 81 00 00 00 00 04 00

0x30: 89 56 00 00 00 FF FF FF FF FF FF FF FF FF FF FF

0x40: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

WIC Slot 1:

2nd generation - FXO Voice daughter card (4 port)

Hardware Revision : 5.0

Top Assy. Part Number : 800-21589-02

Board Revision : A0

Deviation Number : 0-0

Fab Version : 04

PCB Serial Number : FOC10440M4U

RMA Test History : 00

RMA Number : 0-0-0-0

RMA History : 00

Product (FRU) Number : VIC2-4FXO

Version Identifier : V01

CLEI Code : CNUIAPRAAA

EEPROM format version 4

EEPROM contents (hex):

0x00: 04 FF 40 00 4C 41 05 00 C0 46 03 20 00 54 55 02

0x10: 42 41 30 80 00 00 00 00 02 04 C1 8B 46 4F 43 31

0x20: 30 34 34 30 4D 34 55 03 00 81 00 00 00 00 04 00

0x30: CB 89 56 49 43 32 2D 34 46 58 4F 89 56 30 31 20

0x40: C6 8A 43 4E 55 49 41 50 52 41 41 41 FF FF FF FF

0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

justingorres · ‎04-01-2009

WIC Slot 2:

FT1 PMC4351

Hardware Revision : 1.2

PCB Serial Number : FOC10505GXJ

Part Number : 73-8346-05

Board Revision : A0

RMA Test History : 00

RMA Number : 0-0-0-0

RMA History : 00

Deviation Number : 0-0

Product (FRU) Number : WIC-1DSU-T1-V2

Top Assy. Part Number : 800-22193-03

CLEI Code : IPUIAPRRAA

EEPROM format version 4

EEPROM contents (hex):

0x00: 04 FF 40 00 52 41 01 02 C1 8B 46 4F 43 31 30 35

0x10: 30 35 47 58 4A 82 49 20 9A 05 42 41 30 03 00 81

0x20: 00 00 00 00 04 00 80 00 00 00 00 CB 94 57 49 43

0x30: 2D 31 44 53 55 2D 54 31 2D 56 32 20 20 20 20 20

0x40: 20 C0 46 03 20 00 56 B1 03 C6 8A 49 50 55 49 41

0x50: 50 52 52 41 41 FF FF FF FF FF FF FF FF FF FF FF

0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

WIC Slot 3:

T1 (1 port) Multi-Flex Trunk WAN daughter card

Hardware revision 1.0 Board revision D0

Serial number 30264715 Part number 800-03568-03

FRU Part Number VWIC-1MFT-T1=

Test history 0x0 RMA number 00-00-00

Connector type PCI

EEPROM format version 1

EEPROM contents (hex):

0x20: 01 20 01 00 01 CD CD 8B 50 0D F0 03 00 00 00 00

0x30: 68 00 00 00 03 04 01 00 FF FF FF FF FF FF FF FF

Thotsaphon Lueangwattanaphong · ‎04-01-2009

Justin,

You need PVDM installed on it.

Do you have a CCO ID? If you do, please check this link.

http://www.cisco.com/cgi-bin/Support/DSP/cisco_prodsel.pl

HTH,

Toshi

justingorres · ‎04-01-2009

I feel partially dumb, ha. Thanks for your help.