04-03-2009 01:21 AM - edited 07-03-2021 05:24 PM
Hi,
I have 2 1240 in bridge. I need to transport on that bridge 3 vlan. I create 3 SSID , I see the dot11 association on both the AP but if I try to ping the remote it doesn't work.
Any suggestion?
Thank you in advance
Giovanni
04-03-2009 06:47 AM
Hi Giovanni,
When in bridge mode, APs only need a single SSID to carry all VLANs. Delete two of the SSIDs, and remove the VLAN configuration from your remaining one. Be sure to configure "infrastructure-ssid" under the "dot11 ssid SSID_NAME" sub-command line.
You'll still need to make sure that you have the proper subinterfaces and bridge-groups. Let me know if that works, and if not please feel free to post your configuration and we'll get it resolved.
Jeff
04-07-2009 04:54 AM
Thank you Jeff,
unfortunately I have to go at the customer site for the test. I will update this conversation as soon as I have news.
Regards
Giovanni
04-17-2009 04:45 AM
Hi Jeff,
finally I can do some test with your suggestion but I don't able to obtain that the bridge carry all Vlan. Only Vlan 1 works.
I attach the config of both the AP.
hostname BridgeRoot
!
dot11 ssid Bridge1PR
authentication open
authentication key-management wpa
infrastructure-ssid
wpa-psk ascii pippo
!
power inline negotiation prestandard source
!
bridge irb
!
interface Dot11Radio0
no ip address
no ip route-cache
!
encryption mode ciphers aes-ccm tkip
!
ssid Bridge1PR
!
antenna transmit right
antenna receive right
channel 2412
station-role root bridge
world-mode dot11d country IT outdoor
bridge-group 1
!
interface FastEthernet0
no ip address
no ip route-cache
duplex auto
speed auto
hold-queue 160 in
!
interface FastEthernet0.1
encapsulation dot1Q 1 native
no ip route-cache
bridge-group 1
no bridge-group 1 source-learning
!
interface FastEthernet0.130
encapsulation dot1Q 130
no ip route-cache
bridge-group 130
no bridge-group 130 source-learning
!
interface FastEthernet0.344
encapsulation dot1Q 344
no ip route-cache
bridge-group 244
no bridge-group 244 source-learning
!
bridge 1 protocol ieee
bridge 1 route ip
================================================================================================================
hostname BridgenoRoot
!
dot11 ssid Bridge1PR
authentication open
authentication key-management wpa
infrastructure-ssid
wpa-psk ascii pippo
!
bridge irb
!
interface Dot11Radio0
no ip address
no ip route-cache
!
encryption mode ciphers aes-ccm tkip
!
ssid Bridge1PR
!
antenna transmit right
antenna receive right
station-role non-root bridge
world-mode dot11d country IT outdoor
bridge-group 1
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
!
interface FastEthernet0
no ip address
no ip route-cache
duplex auto
speed auto
hold-queue 160 in
!
interface FastEthernet0.1
encapsulation dot1Q 1 native
no ip route-cache
bridge-group 1
no bridge-group 1 source-learning
!
interface FastEthernet0.130
encapsulation dot1Q 130
no ip route-cache
bridge-group 130
no bridge-group 130 source-learning
!
interface FastEthernet0.344
encapsulation dot1Q 344
no ip route-cache
bridge-group 244
no bridge-group 244 source-learning
!
bridge 1 protocol ieee
bridge 1 route ip
I done some test with different configuration but always only the Vlan 1 was OK.
Regards
Giovanni
04-17-2009 05:15 AM
To fix:
dot11 ssid Bridge1PR
vlan 1
interface Dot11Radio0
no encryption mode ciphers aes-ccm tkip
encryption vlan 1 mode ciphers aes-ccm tkip
interface Dot11Radio0.1
encap dot1q 1 native
bridge-group 1
interface Dot11Radio0.130
encap dot1q 130
bridge-group 130
interface Dot11Radio0.344
encap dot1q 344
bridge-group 244 !note typo matches current configs
04-17-2009 07:00 AM
Thank you, it's work!
Regards
Giovanni
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: