cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
9822
Views
0
Helpful
7
Replies

Latest version of ASDM and PIX for a 515E

ece344609_2
Level 1
Level 1

Hi all,

What is the latest supported version of PIX and ASDM for a 515E?

Thanks a bunch.

1 Accepted Solution

Accepted Solutions

PIX Interim Release 8.0.4.28

View solution in original post

7 Replies 7

thomuff
Level 3
Level 3

I am pretty sure it is 8.04 and ASDM Interim Release 6.1.5.51

Make sure to check your memory requirements.

PIX Interim Release 8.0.4.28

Hey Tom,

Sorry for dropping the ball on this. Thanks so much for the info.

Would you hapen to point me to step by step directions to do this upgrade?

Thanks a bunch.

what version on pix are you upgrading from?

BrinksArgentina
Level 1
Level 1

To install 7.0 or 8.0 images you need: 64MB RAM (Restricted license) or 128MB RAM (Failover and Unrestricted licenses)

http://www.cisco.com/en/US/prod/collateral/vpndevc/ps5708/ps5709/ps2030/prod_bulletin0900aecd8023c8d4.html

This is the document:

Guide for Cisco PIX 6.2 and 6.3 Users Upgrading to Cisco PIX Software Version 7.0

http://www.cisco.com/en/US/docs/security/asa/asa70/pix_upgrade/upgrade/guide/pixupgrd.html

Usually, on the first boot the PIX itself migrate deprecated commands, but you need to test everything, especialy VPNs to non Cisco devices.


If it was usefull to you, please rate. Thanks!

Thanks brinks. I finally happened to get the config, Here it is:

Cisco PIX Firewall Version 6.3(5)125

Cisco PIX Device Manager Version 3.0(4)

Compiled on Thu 01-Feb-07 15:13 by morlee

fw1 up 65 days 22 hours

Hardware: PIX-515E, 32 MB RAM, CPU Pentium II 433 MHz

Flash E28F128J3 @ 0x300, 16MB

BIOS Flash AM29F400B @ 0xfffd8000, 32KB

0: ethernet0: address is 0011.20b6.1b50, irq 10

1: ethernet1: address is 0011.20b6.1b51, irq 11

2: ethernet2: address is 0002.b3ee.ef03, irq 11

Licensed Features:

Failover: Disabled

VPN-DES: Enabled

VPN-3DES-AES: Enabled

Maximum Physical Interfaces: 3

Maximum Interfaces: 5

Cut-through Proxy: Enabled

Guards: Enabled

URL-filtering: Enabled

Inside Hosts: Unlimited

Throughput: Unlimited

IKE peers: Unlimited

What are my upgrade options given this info? Thanks.

You miss the last line of the sh ver, just before the serial number show if it is a restricted or unrestricted.

You doesn't have the failover license, so if is a "restricted" version, you can buy 64MB from Cisco.

If you have an Unrestricted license, you need the PIX-515-MEM-128= memory module.

For testing only, you can install a DIMM PC 133. I use a KVR133X64X3/128. But is higer than the original, so i can't close the top!

This is my output

FW1-LAB# sh ver

Cisco PIX Security Appliance Software Version 8.0(3)19

Device Manager Version 6.1(1)

Compiled on Mon 16-Jun-08 11:30 by builders

System image file is "flash:/pix803-19.bin"

Config file at boot was "startup-config"

FW1-LAB up 41 secs

Licensed features for this platform:

Maximum Physical Interfaces : 6

Maximum VLANs : 25

Inside Hosts : Unlimited

Failover : Active/Active

VPN-DES : Enabled

VPN-3DES-AES : Enabled

This platform has an Unrestricted (UR) license.

Serial Number: xxxxxx


Regards

Guido.

Please rate all the helpful comments.

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: