cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
1938
Views
10
Helpful
10
Replies

ISDN Error message - Can anyone help

darkbeatzz
Level 1
Level 1

Hi

I have Cisco IOS Software, 1841 Software (C1841-IPBASE-M), Version 12.4(1c)

trying to do and ISDN test call and get the following erro

01:46:14: ISDN BR0/1/0 **ERROR**: host_disconnect_ack: Unfound B-channel on Disconnect_Ack call id 0x8005

01:46:36: ISDN BR0/1/0 **ERROR**: CCBRI_Go: NO CCB Src->HOST call id 0x8005, event 0x5 ces 1

woods#sh isdn status

Global ISDN Switchtype = basic-net3

ISDN BRI0/1/0 interface

dsl 2, interface ISDN Switchtype = basic-net3

Layer 1 Status:

DEACTIVATED

Layer 2 Status:

Layer 2 NOT Activated

Layer 3 Status:

0 Active Layer 3 Call(s)

Active dsl 2 CCBs = 0

The Free Channel Mask: 0x80000003

Total Allocated ISDN CCBs = 0

would anyone have any ideas?

10 Replies 10

lamav
Level 8
Level 8

Hi:

Can you post the config?

Are you sure about the switch type?

SPIDs?

What about the number you are dialing? Is it valid?

http://www.cisco.com/en/US/tech/tk801/tk379/technologies_tech_note09186a0080094b76.shtml#deactivated

Victor

interface BRI0/1/0

no ip address

encapsulation ppp

dialer pool-member 1

isdn switch-type basic-net3

isdn caller 1234455

no cdp enable

ppp authentication chap

ppp multilink

end

positive about switch type

I wonder does the image allow me to dial out?

woods#sh ver

Cisco IOS Software, 1841 Software (C1841-IPBASE-M), Version 12.4(1c), RELEASE SOFTWARE (fc1)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2005 by Cisco Systems, Inc.

Compiled Tue 25-Oct-05 17:10 by evmiller

ROM: System Bootstrap, Version 12.4(13r)T, RELEASE SOFTWARE (fc1)

woods uptime is 2 hours, 4 minutes

System returned to ROM by power-on

System image file is "flash:c1841-ipbase-mz.124-1c.bin"

Cisco 1841 (revision 7.0) with 114688K/16384K bytes of memory.

Processor board ID FCZ121794A1

2 FastEthernet interfaces

1 ISDN Basic Rate interface

DRAM configuration is 64 bits wide with parity disabled.

191K bytes of NVRAM.

31360K bytes of ATA CompactFlash (Read/Write)

Configuration register is 0x2102

Mick

I do not think that it is an issue with the copy of IOS that you are running. As long as the IOS recognizes the BRI interface it should support dialing activity on the interface.

I believe that there is a significant hint about the issue in your original post:

Layer 1 Status:

DEACTIVATED

Layer 2 Status:

Layer 2 NOT Activated

If layer 1 is deactivated and layer 2 is not activated, then this is the first problem that you need to solve. I would suggest that you check on these things:

- is the router interface correctly connected to the circuit?

- is the circuit to which it connects activated?

- is the circuit to which it connects a digital circuit and not an analog circuit?

- I would suggest checking the switch type but you say that you are positive that this is correct.

HTH

Rick

HTH

Rick

Hi

when I try to call the router i can see the incoming call and the 3 layers look good.

woods#sh isdn status

Global ISDN Switchtype = basic-net3

ISDN BRI0/1/0 interface

dsl 2, interface ISDN Switchtype = basic-net3

Layer 1 Status:

ACTIVE

Layer 2 Status:

TEI = 80, Ces = 1, SAPI = 0, State = MULTIPLE_FRAME_ESTABLISHED

Layer 3 Status:

0 Active Layer 3 Call(s)

Active dsl 2 CCBs = 0

The Free Channel Mask: 0x80000003

Total Allocated ISDN CCBs = 0

Mick

I agree that this looks good up through layer 3. In your original post the ISDN layer 1 status was deactivated. In this post the layer 1 status is Active. Did anything change between the original post and this one?

If you are still having problems I would suggest that it might be helpful to have the output of debug isdn q931.

HTH

Rick

HTH

Rick

Hi Rick,

nothing has changed. the only thing I did was to make the call inbound which brings up all the layers.

here is debug q931

18:36:24: ISDN BR0/1/0 **ERROR**: host_disconnect_ack: Unfound B-channel on Disconnect_Ack call id 0x8023

18:36:46: ISDN BR0/1/0 **ERROR**: CCBRI_Go: NO CCB Src->HOST call id 0x8023, event 0x5 ces 1

Likely a bug, try upgrading to 12.4(3j).

Cisco IOS Software, 1841 Software (C1841-IPBASE-M), Version 12.4(1c), RELEASE SOFTWARE (fc1)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2005 by Cisco Systems, Inc.

Compiled Tue 25-Oct-05 17:10 by evmiller

ROM: System Bootstrap, Version 12.4(13r)T, RELEASE SOFTWARE (fc1)

woods uptime is 20 hours, 15 minutes

System returned to ROM by power-on

System image file is "flash:c1841-ipbase-mz.124-1c.bin"

I can not find anything on the image in the software advisory to check for bugs etc. it does not recognise the image name!

Hi,

I have upgraded to

woods#sh ver

Cisco IOS Software, 1841 Software (C1841-IPBASEK9-M), Version 12.4(24)T, RELEASE SOFTWARE (fc1)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2009 by Cisco Systems, Inc.

Compiled Wed 25-Feb-09 16:11 by prod_rel_team

ROM: System Bootstrap, Version 12.4(13r)T, RELEASE SOFTWARE (fc1)

woods uptime is 10 minutes

System returned to ROM by reload at 11:43:59 GMT Wed Apr 15 2009

System image file is "flash:c1841-ipbasek9-mz.124-24.T.bin"

and the issue is now resolved.

thanks for your help

Hello Mick,

under the BRI interface you need commands to specify how the router should do the call

isdn caller is just a call screening on received calls

you need to use

dialer string

or

dialer map ip

commands to make the router able to perform a call for DDR purposes.

Edit:

you are using a dialer interface so you need to put the calling commands under the dialer interface that uses pool 1.

You haven't provided your interface dialer config so the notes above are valid for the logical interface.

Sorry for the confusion.

Hope to help

Giuseppe

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: