04-20-2009 06:10 PM - edited 03-06-2019 05:17 AM
All,
I am suspecting some loop issue in my LAN. Below is my switch show cam result.
VLAN Dest MAC/Route Des [CoS] Destination Ports or VCs / [Protocol Type]
---- ------------------ ----- -------------------------------------------
21 00-11-0a-33-c5-82 2/2 [IP]
20 00-11-0a-33-c5-82 15/2 [IP]
22 00-11-0a-33-c5-82 15/2 [IP]
17 00-11-0a-33-c5-82 15/2 [IP]
16 00-11-0a-33-c5-82 15/2 [IP]
18 00-11-0a-33-c5-82 15/2 [IP]
12 00-11-0a-33-c5-82 15/2 [IP]
13 00-11-0a-33-c5-82 15/2 [IP]
14 00-11-0a-33-c5-82 15/2 [IP]
15 00-11-0a-33-c5-82 15/2 [IP]
11 00-11-0a-33-c5-82 15/2 [IP]
Total Matching CAM Entries Displayed =11
If the port is 15/1 its a msfc.What is port 15/2?.
********> show version
WS-C6509 Software, Version NmpSW: 6.3(2)
Copyright (c) 1995-2001 by Cisco Systems
NMP S/W compiled on Oct 4 2001, 23:44:35
System Bootstrap Version: 6.1(4)
Hardware Version: 3.0 Model: WS-C6509 Serial #: TBP05490023
PS1 Module: WS-CAC-2500W Serial #: ART054800CS
PS2 Module: WS-CAC-2500W Serial #: ART054800G8
Mod Port Model Serial # Versions
--- ---- ------------------- ----------- --------------------------------------
1 2 WS-X6K-SUP2-2GE SAD054102TA Hw : 3.2
Fw : 6.1(4)
Fw1: 6.1(3)
Sw : 6.3(2)
Sw1: 6.3(2)
WS-F6K-PFC2 SAD054104UG Hw : 2.0
2 2 WS-X6K-SUP2-2GE SAD054102P7 Hw : 3.2
Fw : 6.1(4)
Fw1: 6.1(3)
Sw : 6.3(2)
Sw1: 6.3(2)
WS-F6K-PFC2 SAD054104HU Hw : 2.0
3 48 WS-X6348-RJ-45 SAL0547ETXF Hw : 6.0
Fw : 5.4(2)
Sw : 6.3(2)
WS-F6K-VPWR Hw : 1.0
4 48 WS-X6348-RJ-45 SAL0547ENV1 Hw : 6.0
Fw : 5.4(2)
Sw : 6.3(2)
WS-F6K-VPWR Hw : 1.0
5 48 WS-X6348-RJ-45 SAL0547ESP9 Hw : 6.0
Fw : 5.4(2)
Sw : 6.3(2)
WS-F6K-VPWR Hw : 1.0
7 48 WS-X6348-RJ-45 SAL06355A00 Hw : 6.1
Fw : 5.4(2)
Sw : 6.3(2)
WS-F6K-VPWR Hw : 1.0
8 8 WS-X6408A-GBIC SAL08123ATX Hw : 3.0
Fw : 5.4(2)
Sw : 6.3(2)
9 8 WS-X6408A-GBIC SAL08123AQA Hw : 3.0
Fw : 5.4(2)
Sw : 6.3(2)
15 1 WS-F6K-MSFC2 SAD054105U1 Hw : 1.2
Fw : 12.1(8a)E5
Sw : 12.1(8a)E5
16 1 WS-F6K-MSFC2 SAD054106CN Hw : 1.2
Fw : 12.1(8a)E5
Sw : 12.1(8a)E5
DRAM FLASH NVRAM
Module Total Used Free Total Used Free Total Used Free
------ ------- ------- ------- ------- ------- ------- ----- ----- -----
1 130944K 63378K 67566K 32768K 15002K 17766K 512K 361K 151K
04-20-2009 07:56 PM
"If the port is 15/1 its a msfc.What is port 15/2?"
You have redundant supervisors in your chassis so 15/2 is the MSFC in your second supervisor.
Jon
04-20-2009 08:26 PM
Jon,
Yes I have redundant sup engine but it is port 16/1.
Will the mac learn via msfc card also?
04-21-2009 01:41 AM
"Yes I have redundant sup engine but it is port 16/1."
My mistake - good point :-)
Jon
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: