cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
332
Views
0
Helpful
2
Replies

CUCM6.1 Selecting DSP Resources

Chuan Liu
Level 1
Level 1

Hi,

I have 2 2811 holding HW DSP. I have swapped a PVDM2-64 into 2811A. No configurations of 4 XCODER and 2 CFB profiles were made.

Now, the phones always try to use DSP in 2811B, which has only 4 XCODER. I was thinking the new DSP in 2811A is not working. But they are registered correctly with CUCM. 'show voice dsp group all' shows all 4 DSP's are up.

I tried to force the phone to use the new resources by creating one MRG that only has the XCODER points to the new 2811A. Put the MRG into a new MRGL and associate it with a specific phone via a DP. But the when I make a call between 729 and 711 phones, the other 2811B resources are always used even if they are not in the MRGL. The new resources in 2811A can not be used.

How can I force a test call to use only the new resources?

Thanks in advance.

2 Replies 2

Hi,

you can do this test

Put the needed resource in a MRG

And the not needed one must be in another MRG [don't let it free]

Then assign the needed one to MRGL and assign it to your phone directly to have first priority

If not working, so some configuration issues may be in your gateway

Thanks

Hi,

I did exactly as you said with no success.

This gateway with PVDM2-64 is configured with 2 profiles: one XCODE with 6 sessions and one CFB with 2 sessions. The CFB is working fine. One BRI card and one E1 card are installed in this router. Here is the 'show voice dsp gro all':

----------------------

sh voice dsp gro all

DSP groups on slot 0:

dsp 1:

State: UP, firmware: 4.4.24

Max signal/voice channel: 16/16

Max credits: 240

Group: FLEX_GROUP_VOICE, complexity: FLEX

Shared credits: 240, reserved credits: 0

Signaling channels allocated: 16

Voice channels allocated: 0

Credits used: 0

Group: FLEX_GROUP_XCODE, complexity: HIGH

Shared credits: 0, reserved credits: 0

Transcoding channels allocated: 0

Credits used: 0

dsp 2:

State: UP, firmware: 4.4.24

Max signal/voice channel: 16/16

Max credits: 240

Group: FLEX_GROUP_VOICE, complexity: FLEX

Shared credits: 240, reserved credits: 0

Signaling channels allocated: 16

Voice channels allocated: 0

Credits used: 0

Group: FLEX_GROUP_XCODE, complexity: HIGH

Shared credits: 0, reserved credits: 0

Transcoding channels allocated: 0

Credits used: 0

dsp 3:

State: UP, firmware: 4.4.24

Max signal/voice channel: 16/16

Max credits: 240

Group: FLEX_GROUP_XCODE, complexity: HIGH

Shared credits: 0, reserved credits: 240

Transcoding channels allocated: 0

Credits used: 0

dsp 4:

State: UP, firmware: 1.1.1

Max signal/voice channel: 16/16

Max credits: 240

Group: FLEX_GROUP_CONF, complexity: CONFERENCE

Shared credits: 0, reserved credits: 240

Conference session: 2

Credits used: 0

DSP groups on slot 1:

This command is not applicable to slot 1

DSP groups on slot 2:

This command is not applicable to slot 2

0 DSP resource allocation failure

-------------------

sh dspf ds al

SLOT DSP VERSION STATUS CHNL USE TYPE RSC_ID BRIDGE_ID PKTS_TXED PKTS_RXED

0 3 4.4.24 UP N/A FREE xcode 1 - - -

0 3 4.4.24 UP N/A FREE xcode 1 - - -

0 3 4.4.24 UP N/A FREE xcode 1 - - -

0 3 4.4.24 UP N/A FREE xcode 1 - - -

0 3 4.4.24 UP N/A FREE xcode 1 - - -

0 3 4.4.24 UP N/A FREE xcode 1 - - -

0 4 1.1.1 UP N/A FREE conf 2 - - -

0 4 1.1.1 UP N/A FREE conf 2 - - -

Total number of DSPFARM DSP channel(s) 8

------------------------

Both XCODE and CFB are registered in CUCM.

Thanks.

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: