04-29-2009 02:19 AM - edited 03-04-2019 04:34 AM
hi
The following error displayed in console.Please help me to boot this router
error:
System Bootstrap, Version 12.2(8r)T2, RELEASE SOFTWARE (fc1)
TAC Support: http://www.cisco.com/tac
Copyright (c) 2002 by cisco Systems, Inc.
c3745 processor with 196608 Kbytes of main memory
Main memory is configured to 64 bit mode with parity disabled
Readonly ROMMON initialized
rommon 1 >
thanks in advance
04-29-2009 04:02 AM
Hi,
Its not an error , your device is in rommon mode.Please find the below link to recover the device from rommon mode:-
http://www.cisco.com/en/US/products/hw/routers/ps282/products_tech_note09186a008075fd05.shtml#rmon11
or
http://www.cisco.com/en/US/products/hw/routers/ps274/products_tech_note09186a008009429f.shtml
Hope this helps.
Regards
Sum
05-01-2009 09:23 PM
hi
the following messages displayed
System Bootstrap, Version 12.2(8r)T2, RELEASE SOFTWARE (fc1)
TAC Support: http://www.cisco.com/tac
Copyright (c) 2002 by cisco Systems, Inc.
c3745 processor with 196608 Kbytes of main memory
Main memory is configured to 64 bit mode with parity disabled
Readonly ROMMON initialized
program load complete, entry point: 0x80008000, size: 0x6af738
Error : compressed image checksum is incorrect 0x87CF42D9
Expected a checksum of 0x42EF42D9
*** System received a Software forced crash ***
signal= 0x17, code= 0x5, context= 0x0
PC = 0x800080d4, Cause = 0x20, Status Reg = 0x3041a803
System Bootstrap, Version 12.2(8r)T2, RELEASE SOFTWARE (fc1)
TAC Support: http://www.cisco.com/tac
Copyright (c) 2002 by cisco Systems, Inc.
c3745 processor with 196608 Kbytes of main memory
Main memory is configured to 64 bit mode with parity disabled
Readonly ROMMON initialized
rommon 1 >
05-02-2009 09:17 AM
Try realoding the image or boot straight without writing to flash, using the option in tftpdnld.
05-06-2009 09:45 PM
Hi
After reloading new image the follwing error displayed.
Copyright (c) 2002 by cisco Systems, Inc.
c3745 processor with 196608 Kbytes of main memory
Main memory is configured to 64 bit mode with parity disabled
Readonly ROMMON initialized
program load complete, entry point: 0x80008000, size: 0x11605dc
*** TLB (Load/Fetch) Exception ***
Access address = 0x7074e
PC = 0x8040ad90, Cause = 0x8, Status Reg = 0x3041a803
monitor: command "boot" aborted due to exception
System Bootstrap, Version 12.2(8r)T2, RELEASE SOFTWARE (fc1)
TAC Support: http://www.cisco.com/tac
Copyright (c) 2002 by cisco Systems, Inc.
c3745 processor with 196608 Kbytes of main memory
Main memory is configured to 64 bit mode with parity disabled
Readonly ROMMON initialized
rommon 1 >
Regs
S.Mohan
05-06-2009 09:53 PM
Were you trying to upgrade the memory before this error message started appearing?
05-06-2009 11:51 PM
No.Nothing changed in hardware.i am reloading image through rommon mode with xmodem command.
regs
s.mohan
05-07-2009 01:06 AM
Hi ,
Another simple way to load new image is first load the image in RAM using xmodem command ie ..
xmodem filename -r
Router boots with the image stored in DRAM.
After that make sure that router is not reloaded until you load the image to flash using tftp server.
Once you load the image using tftp reload the router and make sure that config-reg value must be 0x2102.
If you face the same problem after following the above procedure check the flash once.
Hope this helps you.
Thanks,
Satish
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide