cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
5934
Views
0
Helpful
7
Replies

MeetMe Conference: Get "No Conference Bridge" after pressing MeetMe softkey and conference extension...

brandon.kallas
Level 1
Level 1

Configured MeetMe using the UC500_Meetme_Conferencing.pdf document.  After pressing the MeetMe softkey and entering 600 (conference extension) get a busy tone and message on phone that says "No Conference Bridge".   Here is my MeetMe Configuration below....

voice-card 0
no dspfarm
dsp services dspfarm
.

.

.

.

sccp local Loopback0
sccp ccm 10.1.1.1 identifier 1 version 4.0
sccp
!
sccp ccm group 1
associate ccm 1 priority 1
associate profile 1 register 1234567890
!
dspfarm profile 1 conference 
codec g711ulaw
codec g711alaw
codec g729ar8
codec g729abr8
codec g729r8
codec g729br8
maximum sessions 1
associate application SCCP
!
.

.

.

.

telephony-service
sdspfarm units 5
sdspfarm tag 1 1234567890
conference hardware

.

transfer-system full-consult

.

.

.

.

ephone-template  9
softkeys idle  Redial HLog Cfwdall Newcall Pickup Dnd
softkeys seized  Redial Cfwdall Pickup Callback Meetme
softkeys connected  Hold Trnsfer TrnsfVM Endcall Park Confrn ConfList RmLstC LiveRcd Select Join
.

.

.

.

ephone-dn  95  dual-line
number 550
conference meetme
no huntstop
!
!
ephone-dn  96  dual-line
number 550
conference meetme
preference 1
no huntstop
!
!
ephone-dn  97  dual-line
number 550
conference meetme
preference 2
no huntstop
!
!
ephone-dn  98  dual-line
number 550
conference meetme
preference 3
no huntstop
!

.

.

.

ephone  23
conference admin
device-security-mode none
video
mac-address 001C.5840.E771
ephone-template 9
username "tarea" password password
paging-dn 1
type 7940
button  1:29 2s55
night-service bell
!

7 Replies 7

Eivind Jonassen
Level 4
Level 4

What is the output from "show dspfarm all"???

It should be something like:

Dspfarm Profile Configuration

  Profile ID = 2, Service = CONFERENCING, Resource ID = 2  

Profile Description :  

Profile Admin State : UP 

Profile Operation State : ACTIVE 

Application : SCCP   Status : ASSOCIATED 

Resource Provider : FLEX_DSPRM   Status : UP 

Number of Resource Configured : 2 

Number of Resource Available : 2

Codec Configuration 

Codec : g711ulaw, Maximum Packetization Period : 30 , Transcoder: Not Required 

Codec : g711alaw, Maximum Packetization Period : 30 , Transcoder: Not Required

Regards
Eivind


UC520#show dspfarm all
Dspfarm Profile Configuration

Profile ID = 1, Service = CONFERENCING, Resource ID = 1
Profile Description :
Profile Service Mode : Non Secure
Profile Admin State : UP
Profile Operation State : RESOURCE ALLOCATED
Application : SCCP   Status : NOT ASSOCIATED
Resource Provider : FLEX_DSPRM   Status : UP
Number of Resource Configured : 1
Number of Resource Available : 1
Codec Configuration
Codec : g711ulaw, Maximum Packetization Period : 30 , Transcoder: Not Required
Codec : g711alaw, Maximum Packetization Period : 30 , Transcoder: Not Required
Codec : g729ar8, Maximum Packetization Period : 60 , Transcoder: Not Required
Codec : g729abr8, Maximum Packetization Period : 60 , Transcoder: Not Required
Codec : g729r8, Maximum Packetization Period : 60 , Transcoder: Not Required
Codec : g729br8, Maximum Packetization Period : 60 , Transcoder: Not Required


SLOT DSP VERSION  STATUS CHNL USE   TYPE    RSC_ID BRIDGE_ID PKTS_TXED PKTS_RXED

0    4   23.8.0   UP     N/A  FREE  conf   1      -         -         -

Total number of DSPFARM DSP channel(s) 1

Check out http://uc500.com/files/CME-4-1-HW-Conf-Tech-Tip.pdf

Regards

Eivind

Are you sure you issued a "no shutdown" underneath the dspfarm profile?? When you create the profile, it automatically go to "shutdown".

Message was edited by: Eivind Jonassen

That worked!  Thank you!

I made the same mistake the first time I created the profile as well :)

Glad I could help.

Regards

Eivind

I've configured another box before using 1 as the profile number, and it worked fine.   Maybe the instructions on how to set it up should be modified to use 100 instead of 1.

Hi,

It actually does in the guide CME-4-1-HW-Conf-Tech-Tip.pdf.

Regards

Eivind

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: