04-30-2009 09:53 AM - edited 03-21-2019 01:04 AM
Configured MeetMe using the UC500_Meetme_Conferencing.pdf document. After pressing the MeetMe softkey and entering 600 (conference extension) get a busy tone and message on phone that says "No Conference Bridge". Here is my MeetMe Configuration below....
voice-card 0
no dspfarm
dsp services dspfarm
.
.
.
.
sccp local Loopback0
sccp ccm 10.1.1.1 identifier 1 version 4.0
sccp
!
sccp ccm group 1
associate ccm 1 priority 1
associate profile 1 register 1234567890
!
dspfarm profile 1 conference
codec g711ulaw
codec g711alaw
codec g729ar8
codec g729abr8
codec g729r8
codec g729br8
maximum sessions 1
associate application SCCP
!
.
.
.
.
telephony-service
sdspfarm units 5
sdspfarm tag 1 1234567890
conference hardware
.
transfer-system full-consult
.
.
.
.
ephone-template 9
softkeys idle Redial HLog Cfwdall Newcall Pickup Dnd
softkeys seized Redial Cfwdall Pickup Callback Meetme
softkeys connected Hold Trnsfer TrnsfVM Endcall Park Confrn ConfList RmLstC LiveRcd Select Join
.
.
.
.
ephone-dn 95 dual-line
number 550
conference meetme
no huntstop
!
!
ephone-dn 96 dual-line
number 550
conference meetme
preference 1
no huntstop
!
!
ephone-dn 97 dual-line
number 550
conference meetme
preference 2
no huntstop
!
!
ephone-dn 98 dual-line
number 550
conference meetme
preference 3
no huntstop
!
.
.
.
ephone 23
conference admin
device-security-mode none
video
mac-address 001C.5840.E771
ephone-template 9
username "tarea" password password
paging-dn 1
type 7940
button 1:29 2s55
night-service bell
!
04-30-2009 10:05 AM
What is the output from "show dspfarm all"???
It should be something like:
Dspfarm Profile Configuration
Profile ID = 2, Service = CONFERENCING, Resource ID = 2
Profile Description :
Profile Admin State : UP
Profile Operation State : ACTIVE
Application : SCCP Status : ASSOCIATED
Resource Provider : FLEX_DSPRM Status : UP
Number of Resource Configured : 2
Number of Resource Available : 2
Codec Configuration
Codec : g711ulaw, Maximum Packetization Period : 30 , Transcoder: Not Required
Codec : g711alaw, Maximum Packetization Period : 30 , Transcoder: Not Required
04-30-2009 10:09 AM
UC520#show dspfarm all
Dspfarm Profile Configuration
Profile ID = 1, Service = CONFERENCING, Resource ID = 1
Profile Description :
Profile Service Mode : Non Secure
Profile Admin State : UP
Profile Operation State : RESOURCE ALLOCATED
Application : SCCP Status : NOT ASSOCIATED
Resource Provider : FLEX_DSPRM Status : UP
Number of Resource Configured : 1
Number of Resource Available : 1
Codec Configuration
Codec : g711ulaw, Maximum Packetization Period : 30 , Transcoder: Not Required
Codec : g711alaw, Maximum Packetization Period : 30 , Transcoder: Not Required
Codec : g729ar8, Maximum Packetization Period : 60 , Transcoder: Not Required
Codec : g729abr8, Maximum Packetization Period : 60 , Transcoder: Not Required
Codec : g729r8, Maximum Packetization Period : 60 , Transcoder: Not Required
Codec : g729br8, Maximum Packetization Period : 60 , Transcoder: Not Required
SLOT DSP VERSION STATUS CHNL USE TYPE RSC_ID BRIDGE_ID PKTS_TXED PKTS_RXED
0 4 23.8.0 UP N/A FREE conf 1 - - -
Total number of DSPFARM DSP channel(s) 1
04-30-2009 10:14 AM
Check out http://uc500.com/files/CME-4-1-HW-Conf-Tech-Tip.pdf
Regards
Eivind
Are you sure you issued a "no shutdown" underneath the dspfarm profile?? When you create the profile, it automatically go to "shutdown".
Message was edited by: Eivind Jonassen
04-30-2009 10:24 AM
That worked! Thank you!
04-30-2009 10:29 AM
I made the same mistake the first time I created the profile as well :)
Glad I could help.
Regards
Eivind
05-01-2009 10:26 AM
I've configured another box before using 1 as the profile number, and it worked fine. Maybe the instructions on how to set it up should be modified to use 100 instead of 1.
05-01-2009 03:54 PM
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: