seek help:I meet a question about 6509

sunxia.vip · ‎05-01-2009

After the 6509 Switch starts,enters directly rommon.Below is the detailed information

Router>en

Router#show ip inter b

Interface IP-Address OK? Method Status Protocol

Vlan1 unassigned YES unset administratively down down

GigabitEthernet1/1 unassigned YES unset administratively down down

GigabitEthernet1/2 unassigned YES unset administratively down down

GigabitEthernet4/1 unassigned YES unset administratively down down

GigabitEthernet4/2 unassigned YES unset administratively down down

GigabitEthernet4/3 unassigned YES unset administratively down down

GigabitEthernet4/4 unassigned YES unset administratively down down

GigabitEthernet4/5 unassigned YES unset administratively down down

GigabitEthernet4/6 unassigned YES unset administratively down down

GigabitEthernet4/7 unassigned YES unset administratively down down

GigabitEthernet4/8 unassigned YES unset administratively down down

Router#

00:01:28: %ONLINE-SP-6-INITFAIL: Module 1: Failed to synchronize Port asic

Router#

Router#host 6509A

00:02:13: %ONLINE-SP-6-TIMER: Module 4, Proc. 0. Failed to bring online because of timer event

00:02:13: %C6KPWR-SP-4-DISABLED: power to module in slot 4 set off (Reset)

Router#confi t

Enter configuration commands, one per line. End with CNTL/Z.

Router(config)#host cisco6509A

Config mode locked out until standby initializes

Router(config)#

%Software-forced reload

sunxia.vip · ‎05-01-2009

Breakpoint exception, CPU signal 23, PC = 0x40299B44

-Traceback= 40299B44 40297C98 4036B8B4 4036B8E4 40401740 4035BA24 4035BA80 4032DFC0 4032EE60 402E1FC4 402DF758 402DF9CC 4029DD1C

$0 : 00000000, AT : 418E0000, v0 : 41D00000, v1 : 00000010

a0 : 41CF3FB0, a1 : FFFFFFFC, a2 : 00000010, a3 : 00000315

t0 : 00000001, t1 : 0000003B, t2 : 50006CA0, t3 : 00000001

t4 : 00000352, t5 : 00000000, t6 : 50006C98, t7 : 003BAF63

s0 : 00000000, s1 : 00000000, s2 : 50329290, s3 : 50329290

s4 : 085ACBFA, s5 : 00000040, s6 : 00009000, s7 : 0000005A

t8 : 0000838A, t9 : 00000000, k0 : 00000000, k1 : 00000000

gp : 418ED8A0, sp : 50006CF0, s8 : 00000000, ra : 40297C98

EPC : 40299B44, ErrorEPC : 0D4CF57B, SREG : 3401F103

MDLO : 99999A5F, MDHI : 00000315, BadVaddr : C1A2A916

CacheErr : E4800000, DErrAddr0 : 1E02000C, DErrAddr1 : 80006B88

Cause 00000024 (Code 0x9): Breakpoint exception

Writing crashinfo to bootflash:crashinfo_20090429-162634

=== Flushing messages (16:26:34 UTC Wed Apr 29 2009) ===

Buffered messages:

00:00:42: RP: Currently running ROMMON from S (Gold) region

00:00:49: %SYS-5-RESTART: System restarted --

Cisco Internetwork Operating System Software

IOS (tm) c6sup2_rp Software (c6sup2_rp-PS-M), Version 12.1(27b)E1, RELEASE SOFTWARE (fc2)

Technical Support: http://www.cisco.com/techsupport

Compiled Thu 12-Oct-06 21:49 by hqluong

00:00:49: %SNMP-5-COLDSTART: SNMP agent on host Router is undergoing a cold start

00:00:49: %SYS-6-BOOTTIME: Time taken to reboot after reload = 14886108 seconds

00:00:48: %SYS-SP-5-RESTART: System restarted --

Cisco Internetwork Operating System Software

IOS (tm) c6sup1_sp Software (c6sup1_sp-SP-M), Version 12.1(27b)E1, RELEASE SOFTWARE (fc2)

Technical Support: http://www.cisco.com/techsupport

Compiled Thu 12-Oct-06 22:26 by hqluong

00:00:50: %C6KENV-SP-4-FANVERCHK: Power-supply 1 inserted is only compatible with Version 1 fan-tray. Please make sure fan is low-output fan-tray

00:00:50: %OIR-SP-6-INSPS: Power supply inserted in slot 1

00:00:50: %C6KPWR-SP-4-PSOK: power supply 1 turned on.

00:00:50: %C6KENV-SP-4-FANVERCHK: Power-supply 2 inserted is only compatible with Version 1 fan-tray. Please make sure fan is low-output fan-tray

00:00:50: %OIR-SP-6-INSPS: Power supply inserted in slot 2

00:01:28: %ONLINE-SP-6-INITFAIL: Module 1: Failed to synchronize Port asic

00:02:13: %ONLINE-SP-6-TIMER: Module 4, Proc. 0. Failed to bring online because of timer event

00:02:13: %C6KPWR-SP-4-DISABLED: power to module in slot 4 set off (Reset)

Queued messages:

00:02:31: %SYS-3-LOGGER_FLUSHING: System pausing to ensure console debuggin

00:02:30: %SYS-SP-3-LOGGER_FLUSHED: System was paused for 00:00:00 to ensure console debugging output.

00:02:31: %OIR-SP-6-CONSOLE: Changing console ownership to switch processor

sunxia.vip · ‎05-01-2009

*** System received a Software forced crash ***

signal= 0x17, code= 0x24, context= 0x618fc684

PC = 0x6012fe38, Cause = 0x1820, Status Reg = 0x34018002

System Bootstrap, Version 5.3(1)

c6k_sup1 processor with 65536 Kbytes of main memory

rommon 1 >

rommon 1 > exit

monitor: command "exit" not found

rommon 2 >

00:00:09: %PFREDUN-6-ACTIVE: Initializing as ACTIVE processor

00:00:10: %OIR-6-CONSOLE: Changing console ownership to route processor

System Bootstrap, Version 12.1(3r)E2, RELEASE SOFTWARE (fc1)

Cat6k-MSFC2 platform with 262144 Kbytes of main memory

rommon 2 >

System Bootstrap, Version 5.3(1)

c6k_sup1 processor with 65536 Kbytes of main memory

rommon 1 >

rommon 2 > boot

Self decompressing the image : ############################################################################################################################################################### [OK]

Restricted Rights Legend

Use, duplication, or disclosure by the Government is

subject to restrictions as set forth in subparagraph

(c) of the Commercial Computer Software - Restricted

Rights clause at FAR sec. 52.227-19 and subparagraph

(c) (1) (ii) of the Rights in Technical Data and Computer

Software clause at DFARS sec. 252.227-7013.

Leo Laohoo · ‎05-01-2009

You need raise a TAC RMA request. Here's the reason why:

00:02:13: %ONLINE-SP-6-TIMER: Module 4, Proc. 0. Failed to bring online because of timer event

00:02:13: %C6KPWR-SP-4-DISABLED: power to module in slot 4 set off (Reset)

It's due to the "timer event".

Hope this helps.