remove/disable dial-peers for 411 calls

Unanswered Question
May 4th, 2009
User Badges:

below is a list of dial-peers that need to be removed (disabled?) from our voice gateway to block outgoing 411 calls. not sure exactly where to start...

disable dial-peer hunting??


dial-peer voice 233 pots

preference 2

destination-pattern 411

incoming called-number ....

direct-inward-dial

port 0/0/0:23

forward-digits 3

!

dial-peer voice 234 pots

preference 2

destination-pattern 8411

incoming called-number ....

direct-inward-dial

port 0/0/0:23

forward-digits 3

!

dial-peer voice 243 pots

preference 2

destination-pattern 411

incoming called-number ....

direct-inward-dial

port 0/0/1:23

forward-digits 3

!

dial-peer voice 244 pots

preference 2

destination-pattern 8411

incoming called-number ....

direct-inward-dial

port 0/0/1:23

forward-digits 3

!

dial-peer voice 253 pots

preference 2

destination-pattern 411

incoming called-number ....

direct-inward-dial

port 1/0:23

forward-digits 3

!

dial-peer voice 254 pots

preference 2

destination-pattern 8411

incoming called-number ....

direct-inward-dial

port 1/0:23

forward-digits 3


thank you for any suggestions.

  • 1
  • 2
  • 3
  • 4
  • 5
Overall Rating: 5 (2 ratings)
Loading.
kelvin.blair Mon, 05/04/2009 - 06:00
User Badges:
  • Silver, 250 points or more

You can simply go under each one of the dialpeers and type shutdown. This will disable those dialpeers. Now this will keep these dialpeers from being matched. There could be another dialpeer that might allowing the same string. If you are requesting to block certain numbers it all depends on the platform you are using. If you are using CME, then take a look at COR (Class of Restriction) in the CME Administration guide. If you are running CM, then all you need to do is create the pattern and specify blocked.



bbtekgraf Mon, 05/04/2009 - 06:11
User Badges:

kelvin,

thank you for the reply. our platform is cm 4.1(3) ..fyi.


we will give this a try after hours this evening and i will post an update.


have a great day!

ciao

kelvin.blair Mon, 05/04/2009 - 06:15
User Badges:
  • Silver, 250 points or more

WOW! thanks for the rating. CM 4.1.3 does have the block feature. It should be located under route option. Select block this pattern and choose call reject.


That should do it..

bbtekgraf Mon, 05/04/2009 - 07:45
User Badges:

i did find a list of route patterns, but do not show one listed for 411. do i need to manually set up a route pattern for 411 and then block this pattern - call rejected, and/or type "shutdown" under each specific dial-peer?


i appreciate the assistance, i just want to make sure i do this correctly.

bbtekgraf Tue, 05/05/2009 - 09:44
User Badges:

is this correct below in config mode:

>dial-peer voice 233

shutdown


??

thanks

will.alvord Tue, 05/05/2009 - 12:28
User Badges:
  • Silver, 250 points or more

Yes, but you have to add the dial-peer type after the dial-peer #.


conf t

dial-peer voice 233 pots

shut

bbtekgraf Mon, 05/11/2009 - 10:58
User Badges:

the shutdown on each 411 dial-peer worked fine.

will the "wr mem" save all of my changes to the compact flash(cisco 2821) in case the router reboots?


Actions

This Discussion