05-04-2009 10:40 PM - edited 02-21-2020 03:26 AM
Dear All,
i had ASA5505.last time when it start to rommon and i was configure tftp to flash in rommon already but when i start up and i show flash it didnot see please see info as below:
ciscoasa# sh fla
Initializing disk0: cache, please wait...Failed.
No files on device
-----------------------------------------------------------------------------------------------------------
ciscoasa# sh ver
Cisco Adaptive Security Appliance Software Version 7.2(1)
Compiled on Wed 31-May-06 14:45 by root
System image file is "tftp://192.168.7.2/asa721-k8.bin"
Config file at boot was "startup-config"
ciscoasa up 9 mins 52 secs
Hardware: ASA5505, 256 MB RAM, CPU Pentium 500 MHz
Internal ATA Compact Flash, 128MB
BIOS Flash M50FW080 @ 0xffe00000, 1024KB
Encryption hardware device : Cisco ASA-5505 on-board accelerator (revision 0x0)
Boot microcode : CNlite-MC-Boot-Cisco-1.2
SSL/IKE microcode: CNlite-MC-IPSEC-Admin-3.03
IPSec microcode : CNlite-MC-IPSECm-MAIN-2.04
0: Int: Internal-Data0/0 : address is 0023.33be.5199, irq 11
1: Ext: Ethernet0/0 : address is 0023.33be.5191, irq 255
2: Ext: Ethernet0/1 : address is 0023.33be.5192, irq 255
3: Ext: Ethernet0/2 : address is 0023.33be.5193, irq 255
4: Ext: Ethernet0/3 : address is 0023.33be.5194, irq 255
5: Ext: Ethernet0/4 : address is 0023.33be.5195, irq 255
6: Ext: Ethernet0/5 : address is 0023.33be.5196, irq 255
7: Ext: Ethernet0/6 : address is 0023.33be.5197, irq 255
8: Ext: Ethernet0/7 : address is 0023.33be.5198, irq 255
9: Int: Internal-Data0/1 : address is 0000.0003.0002, irq 255
10: Int: Not licensed : irq 255
11: Int: Not licensed : irq 255
The Running Activation Key is not valid, using default settings:
Licensed features for this platform:
Maximum Physical Interfaces : 8
VLANs : 3, DMZ Restricted
Inside Hosts : 10
Failover : Disabled
VPN-DES : Enabled
VPN-3DES-AES : Disabled
VPN Peers : 10
WebVPN Peers : 2
Dual ISPs : Disabled
VLAN Trunk Ports : 0
This platform has a Base license.
Serial Number: JMX1242Z1KE
Running Activation Key: 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000
Configuration register is 0x40
Configuration has not been modified since last system restart.
ciscoasa#
-------------------------------------------------------------------------------------------------------
ciscoasa# wr mem
Building configuration...
Cryptochecksum: 2fae3554 0138b992 3a36f491 a5778a90
%Error opening disk0:/.private/startup-config (Invalid DOS media or no media in slot)
Error executing command
How can do it? Please help to
Best Regards,
Join
05-06-2009 11:55 AM
The flash filesystem may be corrupt or damaged. Can you issue a format flash and access the flash then?
05-06-2009 07:26 PM
Dear Sir,
yes, i tried already it still doesn't work....Could let let me know how can i do next?
Best Regards,
Join
05-07-2009 05:09 AM
If you have support w/ Cisco, I would open up a case with them. If not, I would suggest replacing the flash memory.
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: