cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
350
Views
0
Helpful
3
Replies

Unity 5.0 - call handlerwith DID

zeeshan2007
Level 1
Level 1

Dear sir ,

I have three location A ,B and C , we are using cisco unity 5.0 and callmanager in central site (site C) as a centralized model .remaing two remote locations are connected on central site. In (remote site A) we have FXO and in Remote location B we have DID. we are using AA of unity with call handler .In remote location A with FXo when any incoming call land we can hear welcome greeting than it ask us press 1# for English and Press 2 # for Arabic ,when i press 1# i can listen english greeting when i press 2# I can listen arabic.But now my problem is that if I configure same unity call handler /greetings with my Remote location B with DID it gives me only inital greeting.when i press 1# or press 2# nothing happines with DID. but only initial greeting runs when call lands.

Appreciate your help regarding this matter.

3 Replies 3

Dennis Mink
VIP Alumni
VIP Alumni

sounds like a dtmf issue.

check dtmf on the remote location B (assuming cisco equipoment)

For H323

debug h245 asn1

For SIP

debug voip rtp session named-event

Sample output

H323

Aug 21 21:07:37.902: h245_decode_one_pdu: more_pdus = 0, bytesLeftToDecode = 7

Aug 21 21:07:37.902: H245 MSC INCOMING ENCODE BUFFER::= 6D810447200063

Aug 21 21:07:37.902:

Aug 21 21:07:37.902: H245 MSC INCOMING PDU ::=

value MultimediaSystemControlMessage ::= indication : userInput : signal :

{

signalType “9″

duration 100

}

SIP

Aug 21 21:07:37.902: Pt:101 Evt:9 Pkt:04 00 00 >>

Aug 21 21:07:37.902: Pt:101 Evt:9 Pkt:04 00 00 >>

Aug 21 21:07:37.902: Pt:101 Evt:9 Pkt:04 00 00 >>

Aug 21 21:07:37.902: Pt:101 Evt:9 Pkt:04 01 90 >>

Aug 21 21:07:37.902: Pt:101 Evt:9 Pkt:84 03 20 >>

Aug 21 21:07:37.902: Pt:101 Evt:9 Pkt:84 03 20 >>

Aug 21 21:07:37.902: Pt:101 Evt:9 Pkt:84 03 20 >>

see if your key presses are received at all

Please remember to rate useful posts, by clicking on the stars below.

Dear Sir,

As I mention in my last email I have tested a lot of thing now I found one result I have centrial CCM 4.3 and certilized unity in my centrial site and I have four PRIs with DID's. two of the PRI's are terminated in centrial site router and 2 are terminated in DR site router when ever I am trying to use auto attented on certrial site DID's which are terminated in centrial site router where is my CCM its is working fine but when ever I am trying to use auto attented on DR site DID's which are terminated in DR site router its give me same problem which I have mention in my last email my configuration in unity is fine because is start working when I use centrial site DID kindly help me I will be really thankful to you. only inital greetings work on DR sites

I m also attached both router configuration as well I m using MGCP for PRI.

Dear Sir,

As I mention in my last email I have tested a lot of thing now I found one result I have centrial CCM 4.3 and certilized unity in my centrial site and I have four PRIs with DID's. two of the PRI's are terminated in centrial site router and 2 are terminated in DR site router when ever I am trying to use auto attented on certrial site DID's which are terminated in centrial site router where is my CCM its is working fine but when ever I am trying to use auto attented on DR site DID's which are terminated in DR site router its give me same problem which I have mention in my last email my configuration in unity is fine because is start working when I use centrial site DID kindly help me I will be really thankful to you. only inital greetings work on DR sites

I m also attached both router configuration as well I m using MGCP for PRI.

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: