ISDN issue - network-clock-participate??

Unanswered Question
May 12th, 2009
User Badges:

Hi all,


I have an issue with the following command on a new Cisco 2821 router.


network-clock-participate wic 2


when I try to add this command to the router it comes with the following error


WIC slot is empty or does not support clock participate


Any idea? Thanks!

Nour

======================

CCME#show telephony-service

CONFIG (Version=7.0(1))

=====================

Version 7.0(1)

Cisco Unified Communications Manager Express

For on-line documentation please see:

http://www.cisco.com/en/US/products/sw/voicesw/ps4625/tsd_products_support_series_home.html


======================


CCME# show diag

WIC Slot 2:

VWIC2-1MFT-T1/E1 - 1-Port RJ-48 Multiflex Trunk - T1/E1

Hardware Revision : 0.0

Top Assy. Part Number : 800-22628-05

Board Revision : B0

Deviation Number : 94603

Fab Version : 04

PCB Serial Number : FOC121019VG

RMA Test History : 00

RMA Number : 0-0-0-0

RMA History : 00

Product (FRU) Number : VWIC2-1MFT-T1/E1

Version Identifier : V01

EEPROM format version 4

EEPROM contents (hex):

0x00: 04 FF 40 03 FD 41 00 00 C0 46 03 20 00 58 64 05

0x10: 42 42 30 88 00 01 71 8B 02 04 C1 8B 46 4F 43 31

0x20: 32 31 30 31 39 56 47 03 00 81 00 00 00 00 04 00

0x30: CB 90 56 57 49 43 32 2D 31 4D 46 54 2D 54 31 2F

0x40: 45 31 89 56 30 31 20 D9 02 40 C1 FF FF FF FF FF

0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF


========================================


CCME#show ver

Cisco IOS Software, 2800 Software (C2800NM-ADVENTERPRISEK9-M), Version 12.4(22)T, RELEASE SOFTWARE (fc1)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2008 by Cisco Systems, Inc.

Compiled Fri 10-Oct-08 00:05 by prod_rel_team


ROM: System Bootstrap, Version 12.4(13r)T, RELEASE SOFTWARE (fc1)


SC_2821-CCME uptime is 1 week, 6 days, 10 hours, 51 minutes

System returned to ROM by power-on

System restarted at 07:31:29 WST Wed Apr 29 2009

System image file is "flash:c2800nm-adventerprisek9-mz.124-22.T.bin"



This product contains cryptographic features and is subject to United

States and local country laws governing import, export, transfer and

use. Delivery of Cisco cryptographic products does not imply

third-party authority to import, export, distribute or use encryption.

Importers, exporters, distributors and users are responsible for

compliance with U.S. and local country laws. By using this product you

agree to comply with applicable laws and regulations. If you are unable

to comply with U.S. and local laws, return this product immediately.


A summary of U.S. laws governing Cisco cryptographic products may be found at:

http://www.cisco.com/wwl/export/crypto/tool/stqrg.html


If you require further assistance please contact us by sending email to

[email protected].


Cisco 2821 (revision 53.51) with 237568K/24576K bytes of memory.

Processor board ID FTX1246A05Z

2 Gigabit Ethernet interfaces

1 ATM interface

1 terminal line

1 Channelized (E1 or T1)/PRI port

1 Virtual Private Network (VPN) Module

4 Voice FXS interfaces

1 cisco service engine(s)

DRAM configuration is 64 bits wide with parity enabled.

239K bytes of non-volatile configuration memory.

255488K bytes of ATA CompactFlash (Read/Write)


Configuration register is 0x2102


CCME#


  • 1
  • 2
  • 3
  • 4
  • 5
Overall Rating: 0 (0 ratings)
Loading.
Brandon Buffin Tue, 05/12/2009 - 04:24
User Badges:
  • Purple, 4500 points or more

Try entering the following command first:


router(config)#card type t1 1


This is assuming this is a T1 and not an E1.


Hope this helps.


Brandon

Actions

This Discussion