05-18-2009 10:16 AM - edited 03-21-2019 09:16 AM
I have several phones connected to a SPA3102. With one of those phones i have some strange noice when I it pick up . Kind of interruptions of the line.
This phone (brand Topic/Audility) works fine directly on the landline. It also works good on ATA's of other brand (tested on Fritzbox).
I also tested it on a PAP2T. Same problem as on SPA3102.
There is some cryptic information in the syslog:
05-17-2009 12:40:19 Local3.Debug 192.168.0.50 [0]On Hook
05-17-2009 12:40:18 Local3.Debug 192.168.0.50 IDBG:rs:a
05-17-2009 12:40:18 Local3.Debug 192.168.0.50 IDBG:sc-0
05-17-2009 12:40:17 Local3.Debug 192.168.0.50 IDBG:rs:a
05-17-2009 12:40:17 Local3.Debug 192.168.0.50 IDBG:sc-0
05-17-2009 12:40:16 Local3.Debug 192.168.0.50 IDBG:rs:a
05-17-2009 12:40:16 Local3.Debug 192.168.0.50 IDBG:sc-0
05-17-2009 12:40:16 Local3.Debug 192.168.0.50 IDBG:rs:a
05-17-2009 12:40:16 Local3.Debug 192.168.0.50 IDBG:sc-0
05-17-2009 12:40:15 Local3.Debug 192.168.0.50 IDBG:rs:a
05-17-2009 12:40:15 Local3.Debug 192.168.0.50 IDBG:sc-0
05-17-2009 12:40:14 Local3.Debug 192.168.0.50 IDBG:rs:a
05-17-2009 12:40:14 Local3.Debug 192.168.0.50 IDBG:sc-0
05-17-2009 12:40:13 Local3.Debug 192.168.0.50 IDBG:rs:a
05-17-2009 12:40:13 Local3.Debug 192.168.0.50 IDBG:sc-0
05-17-2009 12:40:13 Local3.Debug 192.168.0.50 IDBG:rs:a
05-17-2009 12:40:13 Local3.Debug 192.168.0.50 IDBG:sc-0
05-17-2009 12:40:12 Local3.Debug 192.168.0.50 IDBG:rs:a
05-17-2009 12:40:12 Local3.Debug 192.168.0.50 IDBG:sc-0
05-17-2009 12:40:11 Local3.Debug 192.168.0.50 [0]Off Hook
Can anyone interpret this ?
Thanks,
Mark
Solved! Go to Solution.
05-21-2009 12:03 PM
Hi Mark,
No, we do not have a way of configuring this. It looks like you have found a device that our ATAs are not compatible with.
Regards,
Patrick
-----------
05-18-2009 10:57 AM
Hi Mark,
using 2wire or 4wire cable between Phone and ATA?
Regards,
Tomas
05-18-2009 12:32 PM
Hello Tomas,
I use 4 wire cable. Only 2 wires are used.
There is a LED on the phone. It is illuminated bij the line-current. It flashes a bit on the rithm of what I hear.
When I mesure the current: it goes up and down from 15 to 20 mA.
When I put a second phone in parallel and I thake both off-hook: no problem anymore.
Regards,
Mark
05-18-2009 01:42 PM
Mark,
i have similar problem, please try 2wire cable. Which included in PAP2T or SPA ATAs.
Regards,
Tomas
05-19-2009 09:49 AM
Hello,
2-wire cable does not change anything. I did some more investigations:
I connected the bad phone on the landline. I takes 17 mA current. My official phone takes 39 mA.
Conclusion: the bad phone has too high resistance.
Is there a setting on the spa3102 I can adjust ? Some treshhold for the off-hook-current detection ?
Regards,
Mark.
05-21-2009 12:03 PM
Hi Mark,
No, we do not have a way of configuring this. It looks like you have found a device that our ATAs are not compatible with.
Regards,
Patrick
-----------
05-21-2009 12:23 PM
Hi Patrick
thanks for the reply.
Mark
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: