Cisco 1841 with HWIC-1T

Unanswered Question
May 19th, 2009

Received the Cisco 1841 two weeks ago and configured the Ethernet Interface just fine.

Received the HWIC-1T serial card today. Powered off and unplugged the 1841, attached wrist-strap and inserted the HWIC-1T into an available slot.

Powered up the 1841 but the HWIC-1T is not being recognized. SDM and CLI are not showing a serial interface, just the 2 Ethernet Interfaces.

Is there something else to be done to the 1841 to recognize this serial card?

Show ver:

wat_framerelay#show ver

Cisco IOS Software, 1841 Software (C1841-IPBASE-M), Version 12.4(3i), RELEASE SOFTWARE (fc2)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2007 by Cisco Systems, Inc.

Compiled Wed 28-Nov-07 18:17 by stshen

ROM: System Bootstrap, Version 12.4(13r)T, RELEASE SOFTWARE (fc1)

wat_framerelay uptime is 30 minutes

System returned to ROM by power-on

System image file is "flash:c1841-ipbase-mz.124-3i.bin"

Cisco 1841 (revision 7.0) with 114688K/16384K bytes of memory.

Processor board ID FTX124920D0

2 FastEthernet interfaces

DRAM configuration is 64 bits wide with parity disabled.

191K bytes of NVRAM.

31488K bytes of ATA CompactFlash (Read/Write)

Configuration register is 0x2102

Show interface:

wat_framerelay#show int

FastEthernet0/0 is up, line protocol is up

Hardware is Gt96k FE, address is 0021.a0ee.2d38 (bia 0021.a0ee.2d38)

Description: $ETH-LAN$$ETH-SW-LAUNCH$$INTF-INFO-FE 0$$ES_LAN$$FW_INSIDE$

Internet address is 172.16.101.253/16

MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec,

reliability 255/255, txload 1/255, rxload 1/255

Encapsulation ARPA, loopback not set

Keepalive set (10 sec)

Full-duplex, 100Mb/s, 100BaseTX/FX

ARP type: ARPA, ARP Timeout 04:00:00

Last input 00:00:00, output 00:00:00, output hang never

Last clearing of "show interface" counters never

Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0

Queueing strategy: fifo

Output queue: 0/40 (size/max)

5 minute input rate 0 bits/sec, 1 packets/sec

5 minute output rate 0 bits/sec, 0 packets/sec

3521 packets input, 293616 bytes

Received 2764 broadcasts, 0 runts, 0 giants, 0 throttles

0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored

0 watchdog

0 input packets with dribble condition detected

1266 packets output, 187400 bytes, 0 underruns

0 output errors, 0 collisions, 3 interface resets

0 babbles, 0 late collision, 0 deferred

0 lost carrier, 0 no carrier

0 output buffer failures, 0 output buffers swapped out

FastEthernet0/1 is administratively down, line protocol is down

Hardware is Gt96k FE, address is 0021.a0ee.2d39 (bia 0021.a0ee.2d39)

MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec,

reliability 255/255, txload 1/255, rxload 1/255

Encapsulation ARPA, loopback not set

Keepalive set (10 sec)

Auto-duplex, Auto Speed, 100BaseTX/FX

ARP type: ARPA, ARP Timeout 04:00:00

Last input never, output never, output hang never

Last clearing of "show interface" counters never

Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0

Queueing strategy: fifo

Output queue: 0/40 (size/max)

5 minute input rate 0 bits/sec, 0 packets/sec

5 minute output rate 0 bits/sec, 0 packets/sec

0 packets input, 0 bytes

Received 0 broadcasts, 0 runts, 0 giants, 0 throttles

0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored

0 watchdog

0 input packets with dribble condition detected

0 packets output, 0 bytes, 0 underruns

0 output errors, 0 collisions, 0 interface resets

0 babbles, 0 late collision, 0 deferred

0 lost carrier, 0 no carrier

0 output buffer failures, 0 output buffers swapped out

wat_framerelay#

I have this problem too.
0 votes
  • 1
  • 2
  • 3
  • 4
  • 5
Overall Rating: 0 (0 ratings)
Loading.
skapter Tue, 05/19/2009 - 07:28

I found 1 error in the log:

Slot 0: Unrecognized cookie format for card!

So..is this an IOS version problem? faulty card?

Actions

This Discussion