cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
399
Views
0
Helpful
2
Replies

H323 Gateway - POTS Dial-peers

uccertltd
Level 1
Level 1

Hi There, this issue is causing me much frustration. We are running CUCM 6.1 and a 3845 ISR running advipsvcs 124-15.T8 IOS. Basically, outbound calls are not matching the specific dialpeers that I have configured on the H323 Gateway. We also have a GSM gateway on port 0/2/1 which should be routing mobile calls 69........

We have the following Route Patterns, all set to Discard Digits <none>. The route list is also configured with Discard Digits <none>:

0.14XXX

0.69XXXXXXXX

0.2XXXXXXXXX

0.80XXXXXXXX

0.00!

0.118XX

0.901!

0.11XXX

166

199

100

We have the following Dial-peers configured, but all outbound calls are matching dial-peer 2000:

dial-peer voice 2001 voip

preference 1

destination-pattern 2...

voice-class codec 1

voice-class h323 1

session target ipv4:10.129.20.3

fax rate 7200 bytes 48

fax nsf 000000

fax protocol pass-through g711ulaw

no vad

!

dial-peer voice 2002 voip

preference 2

destination-pattern 2...

voice-class codec 1

voice-class h323 1

session target ipv4:10.129.16.34

fax rate 7200 bytes 48

fax nsf 000000

fax protocol pass-through g711ulaw

no vad

!

dial-peer voice 100 pots

tone ringback alert-no-PI

description **Police**

destination-pattern 100

progress_ind setup enable 3

progress_ind progress enable 8

incoming called-number .

direct-inward-dial

port 0/2/0:15

forward-digits all

!

dial-peer voice 199 pots

tone ringback alert-no-PI

description **Fire Brigade**

destination-pattern 199

progress_ind setup enable 3

progress_ind progress enable 8

port 0/2/0:15

forward-digits all

!

dial-peer voice 166 pots

tone ringback alert-no-PI

description **First Aid**

destination-pattern 166

progress_ind setup enable 3

progress_ind progress enable 8

port 0/2/0:15

forward-digits all

!

dial-peer voice 6969 pots

tone ringback alert-no-PI

description **Mobile Calls**

preference 1

destination-pattern 0.69........

progress_ind setup enable 3

progress_ind progress enable 8

incoming called-number .

direct-inward-dial

port 0/2/1:15

!!

dial-peer voice 2004 pots

tone ringback alert-no-PI

description **Intl**

preference 1

destination-pattern 0.00T

progress_ind setup enable 3

progress_ind progress enable 8

incoming called-number .

direct-inward-dial

port 0/2/0:15

!

dial-peer voice 2005 pots

tone ringback alert-no-PI

description **Greece PSTN**

preference 1

destination-pattern 0.2.........

progress_ind setup enable 3

progress_ind progress enable 8

incoming called-number .

direct-inward-dial

port 0/2/0:15

!

dial-peer voice 2006 pots

tone ringback alert-no-PI

description **Freephone**

preference 1

destination-pattern 0.8.........

progress_ind setup enable 3

progress_ind progress enable 8

incoming called-number .

direct-inward-dial

port 0/2/0:15

!

dial-peer voice 2000 pots

tone ringback alert-no-PI

preference 2

destination-pattern 0.T

progress_ind setup enable 3

progress_ind progress enable 8

incoming called-number .

direct-inward-dial

port 0/2/0:15

!

dial-peer voice 2007 pots

tone ringback alert-no-PI

description **Dir Svcs**

preference 1

destination-pattern 0.1....

progress_ind setup enable 3

progress_ind progress enable 8

incoming called-number .

direct-inward-dial

port 0/2/0:15

2 Replies 2

uccertltd
Level 1
Level 1

Not to worry folks, resolved it after stepping back and looking at the config again...

on the pots dial-peer voice 69 I changed the destination-patter to 069........ and then did forward-digits 10. Works a treat.

uccertltd
Level 1
Level 1

Not to worry folks, resolved it after stepping back and looking at the config again...

on the pots dial-peer voice 69 I changed the destination-patter to 069........ and then did forward-digits 10. Works a treat.

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: