×

Warning message

  • Cisco Support Forums is in Read Only mode while the site is being migrated.
  • Cisco Support Forums is in Read Only mode while the site is being migrated.

Policy Base Routing Switch C4510

Unanswered Question
Jun 1st, 2009
User Badges:

Hi all,


I have a switch c4510R and would like to use PBR(policy-base-routing), was searching on the cisco software advisor and did not find this functionality. So i can not use the PBR into c4510R?


Regards.

  • 1
  • 2
  • 3
  • 4
  • 5
Overall Rating: 3 (1 ratings)
Loading.
cowetacoit Mon, 06/01/2009 - 05:50
User Badges:

it depends on the supervisor card. Post a show version.

Giuseppe Larosa Mon, 06/01/2009 - 05:54
User Badges:
  • Super Silver, 17500 points or more
  • Hall of Fame,

    Founding Member

Hello Ricardo,

the answer is that this depends on the specific type of supervisor you have installed on it.


the newer SUPs 6E and probably 6 L E don't support it.


There have been other threads of collegues that have discovered this.

Other supervisor models support PBR.


see

http://www.cisco.com/en/US/products/hw/switches/ps4324/prod_models_comparison.html


for example sup V 10Ge supports PBR


http://www.cisco.com/en/US/prod/collateral/modules/ps2797/ps6033/product_data_sheet0900aecd801c5c66_ps4324_Products_Data_Sheet.html





Hope to help

Giuseppe


cowetacoit Mon, 06/01/2009 - 09:31
User Badges:

actually PBR is supported on the Sup6 with the newest release 12.2-52.SG. It just came out May 20th. i was waiting for it to be released.

r-barbosa Fri, 06/05/2009 - 07:50
User Badges:

Hi,


sorry, but I was busy in recent days below the show version


cisco WS-C4510R (MPC8540) processor (revision 13) with 524288K bytes of memory.

Processor board ID FOX093200W3

MPC8540 CPU at 800Mhz, Supervisor V-10GE


Regards

r-barbosa Fri, 06/05/2009 - 08:03
User Badges:

Hi Giuslar,


My supervisor is V-10GE, but not supported PBR, at least when I enter the following commands he shows me the option "ip policy"


C4510(config)# interface TenGigabitEthernet 1/1

C4510(config-if)# ip p?

% Unrecognized command

C4510(config-if)#


My IOS is 12.2(52)SG


Regards.

Giuseppe Larosa Fri, 06/05/2009 - 08:14
User Badges:
  • Super Silver, 17500 points or more
  • Hall of Fame,

    Founding Member

Hello Ricardo,

is the interface configured for L3 or a switchport?

I think you need a valid L3 interface to be able to apply PBR (inbound)


Hope to help

Giuseppe


r-barbosa Fri, 06/05/2009 - 10:04
User Badges:

Hi Giuseppe,


sorry, but i configured in the interface vlan, the following.


c4510(config)# interface vlan 2

c4510(config-if)# ip address 172.20.0.1 255.255.0.0

c4510(config-if)# ip p?

% Unrecognized command

c4510(config-if)#


Is this above interface a layer 3 interface?


regards


Giuseppe Larosa Fri, 06/05/2009 - 11:53
User Badges:
  • Super Silver, 17500 points or more
  • Hall of Fame,

    Founding Member

Hello Ricardo,

an SVI interface like vlan2 is a L3 interface indeed.


I wonder if it can be a question of feature set.


May you post

sh ver |inc image


to see the exact image name



Hope to help

Giuseppe


r-barbosa Fri, 06/05/2009 - 12:15
User Badges:

Hi,


the file IOS image is cat4500-ipbasek9-mz.122-52.SG.bin, but i search on the cisco advisor and not found any IOS with support PBR.


Regards.

r-barbosa Fri, 06/05/2009 - 13:28
User Badges:

Hi,


Then i go the software advisor and field Engine CPU not available "Supervisor V-10GE". Then i choose CAT4500-SUP5-10GE and click "Next", when typing PBR its not found. have any suggestions or run the download of another IOS?


Regards

Actions

This Discussion