cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
1086
Views
3
Helpful
14
Replies

Policy Base Routing Switch C4510

r-barbosa
Level 1
Level 1

Hi all,

I have a switch c4510R and would like to use PBR(policy-base-routing), was searching on the cisco software advisor and did not find this functionality. So i can not use the PBR into c4510R?

Regards.

14 Replies 14

cowetacoit
Level 1
Level 1

it depends on the supervisor card. Post a show version.

Giuseppe Larosa
Hall of Fame
Hall of Fame

Hello Ricardo,

the answer is that this depends on the specific type of supervisor you have installed on it.

the newer SUPs 6E and probably 6 L E don't support it.

There have been other threads of collegues that have discovered this.

Other supervisor models support PBR.

see

http://www.cisco.com/en/US/products/hw/switches/ps4324/prod_models_comparison.html

for example sup V 10Ge supports PBR

http://www.cisco.com/en/US/prod/collateral/modules/ps2797/ps6033/product_data_sheet0900aecd801c5c66_ps4324_Products_Data_Sheet.html

Hope to help

Giuseppe

actually PBR is supported on the Sup6 with the newest release 12.2-52.SG. It just came out May 20th. i was waiting for it to be released.

hi,

is release 12.2-52.SG for SUP6E is support for PBR?

Thanks,

ravi

Hi cowetacoit, have you got the PBR succesfully running with the IOS 12.2-52.SG ?

Thanks for your replay.

All the best.

Hi,

above information is very helpfull,

But is there any workaround or alternate to use PBR on SUPs 6E.

Regards,

Ravi

noc@patni.com

Hi,

sorry, but I was busy in recent days below the show version

cisco WS-C4510R (MPC8540) processor (revision 13) with 524288K bytes of memory.

Processor board ID FOX093200W3

MPC8540 CPU at 800Mhz, Supervisor V-10GE

Regards

Hi Giuslar,

My supervisor is V-10GE, but not supported PBR, at least when I enter the following commands he shows me the option "ip policy"

C4510(config)# interface TenGigabitEthernet 1/1

C4510(config-if)# ip p?

% Unrecognized command

C4510(config-if)#

My IOS is 12.2(52)SG

Regards.

Hello Ricardo,

is the interface configured for L3 or a switchport?

I think you need a valid L3 interface to be able to apply PBR (inbound)

Hope to help

Giuseppe

Hi Giuseppe,

sorry, but i configured in the interface vlan, the following.

c4510(config)# interface vlan 2

c4510(config-if)# ip address 172.20.0.1 255.255.0.0

c4510(config-if)# ip p?

% Unrecognized command

c4510(config-if)#

Is this above interface a layer 3 interface?

regards

Hello Ricardo,

an SVI interface like vlan2 is a L3 interface indeed.

I wonder if it can be a question of feature set.

May you post

sh ver |inc image

to see the exact image name

Hope to help

Giuseppe

Hi,

the file IOS image is cat4500-ipbasek9-mz.122-52.SG.bin, but i search on the cisco advisor and not found any IOS with support PBR.

Regards.

That is strange. That release on a Sup V 10G should support PBR.

http://www.cisco.com/en/US/prod/collateral/switches/ps5718/ps4324/product_bulletin_c25-531034_ps6021_Products_Bulletin.html

I was waiting for about 4 months on the new 12.2-52 release because when i bought a sup 6 i assumed it included PBR (and Netflow) but it didn't.

Hi,

Then i go the software advisor and field Engine CPU not available "Supervisor V-10GE". Then i choose CAT4500-SUP5-10GE and click "Next", when typing PBR its not found. have any suggestions or run the download of another IOS?

Regards

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community:

Innovations in Cisco Full Stack Observability - A new webinar from Cisco