Solved: Why can't I ping the loopback interfaces?

news2010a · ‎06-01-2009

Hi, can you help me with this.

From WG4R3 I can't ping Lo0 and Lo1 on WG4R2 and vice and versa. I advertise the respective networks Lo0 and Lo1 via OSPF, so I am not sure if I can understand what's going on. My ultimate goal is to ping lo0:192.20.11.1 on router "Good".

Edison Ortiz · ‎06-02-2009

In R2, you have the following OSPF configuration:

router ospf 4

log-adjacency-changes

network 192.168.4.0 0.0.0.3 area 0

network 192.168.34.0 0.0.0.255 area 0

network 197.4.2.0 0.0.0.255 area 0

network 197.4.3.0 0.0.0.255 area 0

And you have the following L3 interfaces:

interface Loopback0

ip address 197.4.2.1 255.255.255.0

!

interface Loopback1

ip address 197.4.3.1 255.255.255.0

!

interface Ethernet0

ip address 192.168.4.5 255.255.255.252

interface Serial0.1 multipoint

ip address 192.168.4.2 255.255.255.252

interface Serial0.2 point-to-point

ip address 192.168.34.1 255.255.255.0

Noticed, how E0 is missing within the OSPF process? That's the reason there is no neighbor between R2 and R3. You need:

network 192.168.4.4 0.0.0.3 area 0

On R2.

As for changing the frame-relay interface type, you have 2 options:

1) Delete the interface with:

no interface Serial0.1 multipoint

then reboot and recreate the interface.

2) Create another interface with a different number:

no interface Serial0.1 multipoint

interface Serial0.10 point-to-point

ip address 192.168.4.2 255.255.255.252

frame-relay interface-dlci 221

HTH,

__

Edison.

View solution in original post

Edison Ortiz · ‎06-01-2009

Based on the output provided,

WG4R3#show ip ospf neig

Neighbor ID Pri State Dead Time Address Inter

197.4.7.1 0 FULL/ - 00:00:30 192.168.4.10 Seria

I don't see WG4R2 listed as OSPF neighbor, just WG4R4 is listed.

Verify connectivity between these routers and please post the WG4R2 config for further help.

__

Edison.

news2010a · ‎06-01-2009

Please find attached run config for all routers (WG4R1 thru WG4R4).

One thing that I noticed is that on WG4R2, there is a s0.1 interface configured as multipoint. I tried to do it as 's0.1 point-to-point' but that was not accepted by the IOS. I got message saying that 'type cannot be changed'.

Edison Ortiz · ‎06-02-2009

In R2, you have the following OSPF configuration:

router ospf 4

log-adjacency-changes

network 192.168.4.0 0.0.0.3 area 0

network 192.168.34.0 0.0.0.255 area 0

network 197.4.2.0 0.0.0.255 area 0

network 197.4.3.0 0.0.0.255 area 0

And you have the following L3 interfaces:

interface Loopback0

ip address 197.4.2.1 255.255.255.0

!

interface Loopback1

ip address 197.4.3.1 255.255.255.0

!

interface Ethernet0

ip address 192.168.4.5 255.255.255.252

interface Serial0.1 multipoint

ip address 192.168.4.2 255.255.255.252

interface Serial0.2 point-to-point

ip address 192.168.34.1 255.255.255.0

Noticed, how E0 is missing within the OSPF process? That's the reason there is no neighbor between R2 and R3. You need:

network 192.168.4.4 0.0.0.3 area 0

On R2.

As for changing the frame-relay interface type, you have 2 options:

1) Delete the interface with:

no interface Serial0.1 multipoint

then reboot and recreate the interface.

2) Create another interface with a different number:

no interface Serial0.1 multipoint

interface Serial0.10 point-to-point

ip address 192.168.4.2 255.255.255.252

frame-relay interface-dlci 221

HTH,

__

Edison.

news2010a · ‎06-02-2009

You rule! That was it. Thanks!!!