×

Warning message

  • Cisco Support Forums is in Read Only mode while the site is being migrated.
  • Cisco Support Forums is in Read Only mode while the site is being migrated.

MGCP Gateway T1: Is is up or down?

Answered Question
Jun 2nd, 2009
User Badges:

I have a 2811 MGCP gateway in a CCM 4.X environment running IOS 12.4(8c). It has a T1 PRI for inbound calls. If I do a show interface on the router is shows the Serial 0/0/0:0 and all other timeslots (1-23) as down/line protocol down. However, the T1 is still registered in CCM and the last event logged in the router is that interface Serial 0/0/0:0 is up.


Since this configured for MGCP, would that cause this apparent contradiction? If I do a show mgcp endpoints they all show as up.


Thanks

Correct Answer by Nicholas Matthews about 8 years 2 months ago

The b-channels are not required for any type of data and are a place holder in IOS. You are worried about the status of these commands:


show isdn status (multiple frame established)

show isdn service ( 0 is good state )

show controller t1




hth,

nick

Correct Answer by Jaime Valencia about 8 years 2 months ago

At least that T1 is fine based on that output


HTH


java


if this helps, please rate

  • 1
  • 2
  • 3
  • 4
  • 5
Overall Rating: 5 (2 ratings)
Loading.
Jaime Valencia Tue, 06/02/2009 - 08:53
User Badges:
  • Cisco Employee,
  • Hall of Fame,

    2011

If you issue a sh isdn status what's the status?

You should clearly see the status there.

If you call what happens?


HTH


java


if this helps, please rate

gmgarrian Tue, 06/02/2009 - 09:00
User Badges:

Calls are successful, but this is a resent port and I suspect the number was ported to the wrong T1 (there's another T1 at this site.


Here's the output from the sh isdn stat:


Global ISDN Switchtype = primary-ni


%Q.931 is backhauled to CCM MANAGER 0x0003 on DSL 0. Layer 3 output may not appl

y


ISDN Serial0/0/0:23 interface

dsl 0, interface ISDN Switchtype = primary-ni

L2 Protocol = Q.921 0x0000 L3 Protocol(s) = CCM MANAGER 0x0003

Layer 1 Status:

ACTIVE

Layer 2 Status:

TEI = 0, Ces = 1, SAPI = 0, State = MULTIPLE_FRAME_ESTABLISHED

Layer 3 Status:

0 Active Layer 3 Call(s)

Active dsl 0 CCBs = 0

The Free Channel Mask: 0x807FFFFF

Number of L2 Discards = 0, L2 Session ID = 13

Total Allocated ISDN CCBs = 0

Correct Answer
Jaime Valencia Tue, 06/02/2009 - 09:32
User Badges:
  • Cisco Employee,
  • Hall of Fame,

    2011

At least that T1 is fine based on that output


HTH


java


if this helps, please rate

Correct Answer
Nicholas Matthews Tue, 06/02/2009 - 15:28
User Badges:
  • Red, 2250 points or more

The b-channels are not required for any type of data and are a place holder in IOS. You are worried about the status of these commands:


show isdn status (multiple frame established)

show isdn service ( 0 is good state )

show controller t1




hth,

nick

gmgarrian Wed, 06/03/2009 - 06:10
User Badges:

Based on that, everything looks good.


Thanks for the info.

Actions

This Discussion