Finding Memory for Sup2 new IOS version

Answered Question
Jun 8th, 2009

I'm trying to upgrade some old Sup 2's to a new version of IOS. However I need to know how much DRAM is on board to make sure I stay within the requirements (Already know I need a bigger flash card to store the image on).

Other than show ver (pasted below), which doesn't seem to show the right info from what I've read, is there a command to find the amount of DRAm in a sup2?

Thanks!

Cisco Internetwork Operating System Software

IOS (tm) c6sup2_rp Software (c6sup2_rp-DSV-M), Version 12.1(11b)E, EARLY DEPLOYM ENT RELEASE SOFTWARE (fc1)

TAC Support: http://www.cisco.com/tac

Copyright (c) 1986-2002 by cisco Systems, Inc.

Compiled Wed 27-Feb-02 09:08 by eaarmas

Image text-base: 0x40008980, data-base: 0x415B0000

ROM: System Bootstrap, Version 12.1(11r)E1, RELEASE SOFTWARE (fc1)

BOOTLDR: c6sup2_rp Software (c6sup2_rp-DSV-M), Version 12.1(11b)E, EARLY DEPLOYM ENT RELEASE SOFTWARE (fc1)

hq-core uptime is 4 weeks, 6 days, 22 hours, 31 minutes

System returned to ROM by power-on (SP by power-on)

System restarted at 12:06:42 DST Mon May 4 2009

System image file is "bootflash:c6sup22-dsv-mz.121-11b.E.bin"

cisco Catalyst 6000 (R7000) processor with 227328K/34816K bytes of memory.

Processor board ID SAL06230U9D

R7000 CPU at 300Mhz, Implementation 39, Rev 3.3, 256KB L2, 1024KB L3 Cache

Last reset from power-on

Bridging software.

X.25 software, Version 3.0.0.

4 Virtual Ethernet/IEEE 802.3 interface(s)

144 FastEthernet/IEEE 802.3 interface(s)

2 Gigabit Ethernet/IEEE 802.3 interface(s)

381K bytes of non-volatile configuration memory.

16384K bytes of Flash internal SIMM (Sector size 512K).

Configuration register is 0x2102

#show mod

Mod Ports Card Type Model Serial No.

--- ----- -------------------------------------- ------------------ -----------

1 2 Catalyst 6000 supervisor 2 (Active) WS-X6K-S2U-MSFC2 XXXXXXXXXXX

7 48 48 port 10/100 mb RJ45 WS-X6348-RJ-45 XXXXXXXXXXX

8 48 48 port 10/100 mb RJ45 WS-X6348-RJ-45 XXXXXXXXXXX

9 48 48 port 10/100 mb RJ45 WS-X6348-RJ-45 XXXXXXXXXXX

Mod MAC addresses Hw Fw Sw Status

--- ---------------------------------- ------ ------------ ------------ -------

1 0009.1243.853c to 0009.1243.853d 3.7 6.1(3) 7.2(0.35) Ok

7 0003.6c27.a760 to 0003.6c27.a78f 1.4 5.4(2) 7.2(0.35) Ok

8 0003.6c2d.eaa0 to 0003.6c2d.eacf 1.4 5.4(2) 7.2(0.35) Ok

9 0003.6c27.5a20 to 0003.6c27.5a4f 1.4 5.4(2) 7.2(0.35) Ok

Mod Sub-Module Model Serial Hw Status

--- --------------------------- --------------- --------------- ------- -------

1 Policy Feature Card 2 WS-F6K-PFC2 XXXXXXXXXXX 3.2 Ok

1 Cat6k MSFC 2 daughterboard WS-F6K-MSFC2 XXXXXXXXXXX 2.3 Ok

I have this problem too.
0 votes
Correct Answer by Edison Ortiz about 7 years 5 months ago

cisco Catalyst 6000 (R7000) processor with 227328K/34816K bytes of memory

You have 256MB DRAM.

Add the 2 numbers from the line above, remember the 1024 rule.

HTH,

__

Edison.

  • 1
  • 2
  • 3
  • 4
  • 5
Overall Rating: 5 (1 ratings)
Loading.
Correct Answer
Edison Ortiz Mon, 06/08/2009 - 07:57

cisco Catalyst 6000 (R7000) processor with 227328K/34816K bytes of memory

You have 256MB DRAM.

Add the 2 numbers from the line above, remember the 1024 rule.

HTH,

__

Edison.

Actions

This Discussion