06-15-2009 01:44 AM - edited 03-15-2019 06:31 PM
Dear All,
I have callmanager 4.2 integrated with harris pbx using NI2 signalling , when analog phone from pbx call ip phone caller id presented good and appear on the ip phone but when i call from ip phone to PBX the caller id oh ip phone not appeared just appear the extension number , although I allowed "Calling Line ID Presentation*" on the gateway configuration.
your fast replay is highly appreciated.
06-15-2009 01:49 AM
Are you using h.323 or mgcp ?
And, you need to take "debug isdn q931" for the call that gives you problem.
06-15-2009 01:53 AM
I am using mgcp protocol
06-15-2009 02:42 AM
Post the debug q931 output.
Do not enable any additional debug, include the rouble call only, do not use attachments.
06-15-2009 04:01 AM
kindly find attached debug Q931
*Mar 14 14:43:52.754: ISDN Se3/1:15 Q931: TX -> SETUP pd = 8 callref = 0x0001
Bearer Capability i = 0x8090A3
Standard = CCITT
Transfer Capability = Speech
Transfer Mode = Circuit
Transfer Rate = 64 kbit/s
Channel ID i = 0xA9839F
Exclusive, Channel 31
Calling Party Number i = 0x0081, '6578'
Plan:Unknown, Type:Unknown
Called Party Number i = 0x80, '4994'
Plan:Unknown, Type:Unknown
*Mar 14 14:43:52.934: ISDN Se3/1:15 Q931: RX <- CALL_PROC pd = 8 callref = 0x8001
Channel ID i = 0xA9839F
Exclusive, Channel 31
*Mar 14 14:43:52.958: ISDN Se3/1:15 Q931: RX <- ALERTING pd = 8 callref = 0x8001
*Mar 14 14:43:56.910: ISDN Se3/1:15 Q931: RX <- CONNECT pd = 8 callref = 0x8001
Connected Address i = 0xA1, '7593'
*Mar 14 14:43:56.914: ISDN Se3/1:15 Q931: TX -> CONNECT_ACK pd = 8 callref = 0x0001
Gateway#
06-15-2009 04:08 AM
Sorry, I'm not familiar with mgcp to tell you why router does not send calling name.
Hopefully somebody elese will.
06-15-2009 04:46 AM
hi guys,
if anybody can help me?
06-15-2009 04:49 AM
Hi,
Under your router serial interface issue:
isdn outgoing display-ie
Which is off by default.
Edit: to get the name presented you need to select Calling Name Presentation: Allowed. This is in Route Pattern configuration.
Calling Line ID Presentation is for ANI representation, not for names.
And ofcourse, the other PBX must support it.
Are you doing QSIG?
06-15-2009 05:11 AM
First I'd like to thank you for your fast replay , but I configured this command under the serial interface also I allowed the Calling Name Presentation on the route pattern configuration and the problem still not solved.
06-15-2009 06:38 AM
Nothing that you configure on the interface will help, because you're using MGCP.
06-16-2009 06:53 AM
Thanks for all your replies and I solved the problem using ETSI signalling , configuring the PBX as user side and the callmanager as network side , also configured this command under serial interface "isdn protocol-emulate network"
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide